Question about Euro-Pro 7500XH Mechanical Sewing Machine

2 Answers

Instruction on how to thread shark euro sewing machine

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 539 Answers

Turn handwheel toward you.
Lift presser foot up.
Again-make sure that presser foot is UP to allow thread to go into tension disks.
Now it's time to thread those tension disks...ready? OK!
Put thread on spool pin.
Pull thread taut. We don't want any thread hanging down over the machine.
Pull thread slowly, holding taut, and put through first tension disk, and each successive tension disk.
Put thread right to left through take-up lever then gently pull all the way down to next guide until you are directly in front of needle bar.
Almost there now!
Hook thread into slot located in back of needle and then pull thread toward you
Put end of thread from Front of needle eye to the Back of needle eye
Do you have threaded bobbin in the bobbin case? You didn't mention needing help with that , so I will assume you did.
Make sure you have drawn at least 5 inches of thread through your needle.
Pull that needle thread toward you and it
turn handwheel slowly with right hand as you pull that needle thread toward you. The needle will dip down and loop onto the bobbin thread. Tug both threads drawing them up.
Put both thread underneath as well as between the presser foot and let at least 5 to 6 inches of each thread trail behind and under presser foot.
Lower presser foot.
Ready to sew? You bet!
Hope this helps!

Posted on Mar 31, 2012


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 980 Answers

If you can email a picture I can help you

Posted on Mar 07, 2010


4 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


  • 3 Answers

SOURCE: help me find a manual for a euro pro 7133 sewing machine

I hope this helps. It took some searching but this is what i found. Good luck!

Posted on Jan 22, 2010


  • 108 Answers

SOURCE: owners manual for a 650D Euro-pro sewing

i was able to find one at

Posted on Feb 15, 2010


  • 6 Answers

SOURCE: I need to buy a replacement foot for my shark euro...

e mail to or call them at 845-694-4961 and leave a massage

Posted on Jun 14, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Show do I thread the euro shark 60?

I believe it's on the right side back edge of your machine facing you, most machines have arrows printed on the machine for the direction the thread is to be threaded.

Feb 15, 2015 | Euro-Pro Shark 60 - 384

1 Answer

How to thread euro-pro 150 sewing machine

Try looking on here:
Although your model number is not listed, they do have threading diagrams for other Euro-pro machines. Perhaps one is similar enough to your machine to allow you to thread it and get started.
I'm not sure what's happened to the Euro-pro site, it seems to have been taken over by Shark and no longer has a sewing machine manuals section as it did before.
Hope this helps!

Sep 27, 2010 | Euro-Pro 150 Mechanical Sewing Machine

1 Answer

How to install the converter on a Euro Pro Shark serger 101-548

The converter your using is for 2 thread conversions. To use 4 threads you put in second needle

Aug 22, 2009 | Sewing Machines

2 Answers

I have a Shark Euro Pro sewing machine. Thread

Sound as if your tension is to tight. you have to play with it to get it adjusted, be patient.

Aug 07, 2009 | Sewing Machines

1 Answer


I have a pdf copy of a Euro-Pro Shark 417 manual and am willing to share.

Oct 14, 2008 | Sewing Machines

1 Answer

Threading instructions for the euro-pro shark mechanical machine

You can view the manual online at the euro pro web site. Although, I have the manual and I am having the same problem. It was working fine and now for some God only knows reason, I can't seem to thread it right again. This is extremely frustrating for me. The manual doesn't give written instructions there are just picture for you to use as a guide. Here is a link to the manual, I hope you have better luck than me.

Jul 02, 2008 | Euro-Pro 373 Mechanical Sewing Machine

Not finding what you are looking for?
Euro-Pro 7500XH Mechanical Sewing Machine Logo

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Euro-Pro Sewing Machines Experts

Irene Tulloch

Level 2 Expert

498 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Chris Wetmore

Level 2 Expert

190 Answers

Are you an Euro-Pro Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides