Question about Linksys WRT120N Router

1 Answer

Laptop cannot acquire ip address from router even though cable are connected.my router is WRT 120N Linksys. it is already set to get ip address automatically. it ends up having no connectivity. i have reset the router already. i haven't accessed it even once.

Posted by on

  • James Morse May 11, 2010

    What version of windows are you using?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 5 Answers

Make sure your network card is active . for tcp/ip then try resetting all 3 devices router/modem and laptop. (same time) Good Luck.

Posted on Mar 28, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blocking URL's Using Wireless Router with Wireless Connectivity


HERE. look on page 17 of the .PDF, it shows you how to block web addresses and other types of traffic. Its under chapter 2 Access Restrictions > Internet Access

May 29, 2012 | Computers & Internet

1 Answer

Router does not show wireless light. I have reset it but can't access it with the setup wizard. Any suggestions?


* NOTE: If you tried to set-up the WRT-150N Router previously, but failed, with the Router ON, press the "Reset" button on the back panel and hold it down for 10 seconds, then release. This will reset the Router to factory settings and erase all previous data.
then do this :
1. Hook up the Linksys WRT-150N Router to the Modem via a LAN cable.
2. Hook up the Linksys WRT-150N Router to your computer via a LAN cable with the LAN cable in Port #1 on the Linksys WRT-150N Router.
3. Type http://192.168.1.1 in the address bar of your web browser.
4. Log-on to the Linksys WRT-150N Router with these log-on credentials:
Username: linksys (lower-case)
Password: admin (lower-case)
5. Click on the "Clone PC MAC Address" tab.
6. Click the "Clone PC MAC Address" button.
7. Click "Save", click "Continue".
8. Click the "Wireless Security" tab.
9. Choose "WPA2 Personal - TKIP/AES" for encrypted security.
10. Enter encryption password (passphrase).
11. Click "Save", click "Continue".
12. Exit the web browser.
13. Disconnect the LAN cable from the computer and Port #1 on the Linksys WRT-150N Router.
In about 5 seconds, your wireless connection should be up and running.


Sep 15, 2010 | Linksys Wireless-N WRT150N Router

1 Answer

Hello, I have a Linksys Router model No. WRT 160N and have problems with the wireless signal. Doesn't appear the wireless symbol ON and I have connected already the modem cable. The modem is OK cuz I can...


* NOTE: If you tried to set-up the WRT-160N Router previously, but failed, with the Router ON, press the "Reset" button on the back panel and hold it down for 10 seconds, then release. This will reset the Router to factory settings and erase all previous data.
Then do this
1. Hook up the Linksys WRT-160N Router to the modem(cable, DSL or satelitte)
2. Hook up the Linksys WRT-160N Router to your computer via a LAN cable with the LAN cable in Port #1 on the Linksys WRT-160N Router.
3. Type http://192.168.1.1 in the address bar of your web browser.
4. Log-on to the Linksys WRT-160N Router with these log-on credentials:
Username: linksys (lower-case)
Password: admin (lower-case)
5. Click on the "Clone PC MAC Address" tab.
6. Click the "Clone PC MAC Address" button.
7. Click "Save", click "Continue".
8. Click the "Wireless Security" tab.
9. Choose "WPA2 Personal - TKIP/AES" for encrypted security.
10. Enter encryption password (passphrase).
11. Click "Save", click "Continue".
12. Exit the web browser.
13. Disconnect the LAN cable from the computer and Port #1 on the Linksys WRT-160N Router.
In about 5 seconds, your wireless connection should be up and running.

Sep 15, 2010 | Linksys WRT160N Wireless Router

1 Answer

Linksys wrt 120n connected but can't browse


Check your computer's browser settings, make sure it's getting valid IP address, try pinging a website and check your IP settings under network connections.

Disable any third party firewall software you have installed.

Hope this helps!

Jul 20, 2010 | Linksys WRT120N Router

2 Answers

Acquiring network address


Sometimes you have to change your computer's settings or the routers settings to know what type of encryption its looking for otherwise it will just stay on acquiring.

Sep 19, 2009 | Linksys WRH54G Wireless Router

1 Answer

Loss of internet connection to desktop with WRT 160 N


If you do this and post the results I can tell you how to configure the router as you do not need the domain:-

1. connect to modem with an ethernet cable, without the router
2. assuming it's windows, start --> control panel --> Network Connections --> double click on the Local Area Connection --> Click details and post ip address, subnet, default gateway and both dns servers

Jan 20, 2009 | Linksys WRT160N Wireless Router

1 Answer

Having problems with linksys connection


Linksys Wireless-G WRT54G Router



Please check if the router needed IP address?
- if yes? ( goto Network Settings and add the IP address.
- if not? ( obtained you Network Settings do not input IP address.

Double check also if your Router is properly configured?

Sep 21, 2008 | Linksys Wireless-G WRT54G Router

1 Answer

Tiscali wirless connection issue


Sounds like the router may need a firmware update as the DHCP service is failing to run correctly.

You can however just use a static ip address.
First of all find out the network address in use.
eg. 192.168.0.1 - 192.168.1.1 - 192.168.2.1
to find out, - start menu - run - cmd - ok - ipconfig

1. Log on to the client computer as Administrator or as Owner. 2. Click Start, and then click Control Panel. 3. Click Network and Internet Connections. 4. Click Network Connections. 5. Right-click Wireless Network Connection, and then click Properties. 6. Click the General tab, click Internet Protocol (TCP/IP) in the This connection uses the following items list, and then click Properties. 7. In the Internet Protocol (TCP/IP) Properties dialog box, click Obtain an IP address automatically (if it is not already selected), and then click OK.

Note You can also assign a unique static IP address in the range of 192.168.0.2 to 192.168.0.254. For example, you can assign the following static IP address, subnet mask, and default gateway:

IP Address 192.168.0.2
Subnet mask 255.255.255.0
Default gateway 192.168.0.1

Jun 20, 2008 | Linksys WPC54G Wireless-G Notebook Adapter...

2 Answers

Laptop can not connect to router


Hi,

If you care to try, manually enter IP settings in your laptop as follows:
IP Address - 192.168.1.2
Subnet Mask - 255.255.255.0
Default Gateway - 192.168.1.1
DNS - whatever your ISP is using

In your Internet Explorer >
Tools, Internet Options, Connections tab, LAN settings button, check "Automatically detect settings", OK, Advance tab, check Use HTTP 1.1 through proxy connections.

Hope this be of some help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Nov 23, 2007 | Linksys WRT300N Wireless Router

2 Answers

Problem connecting to the net


You router may be set to be DHCP enabled so that it allocates the ip addresses automatically to each pc, so check that the pc's network card with connection problems is set in the properties on the TCP/IP line is set to obtain an ip address automatically. You can also try, Start>run then type ipconfig /flushdns to clear the pc ip address and dns. and restart pc. Lastly if you pc is both network cabled and wireless, ensure one or the other is dissabled as this can confuse the ip adress alocation.

Apr 29, 2007 | Linksys Wireless-G WRT54GR Router

Not finding what you are looking for?
Linksys WRT120N Router Logo

Related Topics:

358 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...