Question about Denon AVR-587

1 Answer

AVR-590 periodically switches from Dolby to PLC affecting picture

While watching our television through the cable box, our Denon AVR-590 will switch from Dolby to PLC causing the picture to show "snow". The picture comes back quickly but obviously an issue. Any help?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 8,546 Answers

It sounds like your cable signal is dropping out. Take it up with th carrier.

Posted on Apr 03, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Switches off after five seconds.AVR-590


There are a few things that could be causing this to happen. The first thing you should do is check all the speaker wires connected to see if they might be touching each other somewhere. What you are describing sounds like there might be a short. Also, is the receiver well ventilated? What is happening is that it is protecting itself but shutting off.The 590 is going in to Protection Mode due to some fault it perceives. The quick flashing red power light (as opposed to a slower flashing light) would indicate either speaker wires touching another terminal, driving 4 ohm speakers to loud, or amp failure.

Jan 18, 2016 | Denon Audio Players & Recorders

1 Answer

Denon AVR - 2807 flickers in TV mode with picture & sound.


Change the hdmi cable and try. If not then you have an hdmi fault module.

Dec 15, 2013 | Denon AVR-2807 Receiver

1 Answer

Denon avr-2113ci hdmi can't change source


Can you update the firmware on the amp as this could also affect the connection between the players.

Jan 15, 2013 | Denon AVR-2113CI

1 Answer

How do I set my receiver to read TV/CBL Dolby Digital. It is a AVR 789


The Dolby digital signal is outputted only through the Optical or Coaxial socket of the CBL box. you will have to get an optic fiber or coaxial cable depending which cable box you have and connect it to the digital input of the Denon receiver. The Denon's digital input are already assigned at the back. Eg: Optic input might be labeled CD so if you are connecting the CBL box to the optic input remember to select CD on the Denon to hear the cable sound, same goes with the coaxial input.

Aug 27, 2011 | Denon AVR-788

1 Answer

I have a Denon AVR 1707 reciever. I am trying to connect my dvd player through RGB cables. The sound works just fine when i turn the reciever to dvd but there is no video. I have the component 2 set to dvd...


The video cables--the green, blue, and red ones must be connected from the video OUT portion of the DVD player to the Component 2 video IN of the Denon. It could be the handshake between your Denon and your television. Do you have anything else to connect to the Denon to see if you get a picture? How are you connecting the Denon to the television? Make sure you have your television on the proper input and check the cables going between it and the Denon.

May 25, 2011 | Denon AVR-1707 Receiver

1 Answer

I have denon avr 987 receiver i messed up settings somehow. when i have receiver set to dolby digital tv i get sound, but no picture. if i switch the setting to DBS i get picture buy no sound. what did...


Are your DD TV and DBS referring to the same source device or are they separate, say, cable Box and Sat Box?

Start over with the digital audio assignments for wherever you plugged in the digital audio cable from (guessing) your Cable TV box (recommended as "TV" is not usually a great source for audio).

The manual:

http://www.retrevo.com/support/Denon-AVR-987-Receivers-manual/id/696dj079/t/2/

You might also want to define the specific cabling of things if more is required. Exact point-to-point paths and cable styles for audio and video.

Dec 31, 2010 | Denon AVR-987 Receiver

2 Answers

How can i connect Nintendo wii to avr-590. Have


To connect a Nintendo Wii to an AVR-590, I am assuming this is a Denon Receiver, you will need to connect the Nintendo Wii to the TV, then connect audio out from the TV to the AVR-590 Receiver, and select the receiver to be in Pro Logic. Depending on the TV, if you have fiberoptic output on the TV, you would hook a fiberoptic out from the TV to the AV Receiver, but you will still not get true Dolby Digital, just Dolby Pro Logic. This will be the most effective way to solve the problem. Hope This Helps

Geek Squad

Dec 28, 2009 | Electronics - Others

1 Answer

The receiver is connected via an Optical audio cable to my Bell ExpressVu HD receiver, When watching HD programming the Dolby Digital breaks up, I then have to switch to "virtual" setting to get sound. I...


my rule is to always install an analog connection to any device along with a digital connection as a "backup", if you will. set the input on the receiver to auto and the rest is like magic with functional equipment. sometimes digital signals do flutter and become intermittent. the receiver will then switch to analog to keep the game goin.

Nov 03, 2009 | Denon AVR-1602 Receiver

1 Answer

Denon Receiver AVR 1602 not playing Dolby Digital w/ Samsung BD


Dolby signals are passed via either an RF cable or optical link. Both the receiver and player need to have these switched on and that they are passing the correct signals. You clearly found the correct setting for the TV sound link. Now you just have to find the one for the DVD player.

Jun 02, 2017 | Denon AVR-3805 Receiver

1 Answer

Denon avr-1909 crackling sound while watching Uverse HD.


It may may the the AT+T box is really not compatible with the AVR or the Pioneer.

Check the specs on those input/outputs for the Ubox and the receiver.
See if they agree. If so, try another hookup method like HDMI ( which carries the audio too)

Nov 05, 2008 | Denon AVR-1905 Receiver

Not finding what you are looking for?
Denon AVR-587 Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Denon Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5699 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Marvin
Marvin

Level 3 Expert

85219 Answers

Are you a Denon Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...