Question about DISH Network 322 DTV Receiver

1 Answer

322 receiver trying to acquire a sat signal for 5 days 0 out of 5 progress please help

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 29 Answers

Hi, Mary with Dish network Customer Service. The issue you are experiencing is a complete satellite signal loss message. If you are experiencing severe weather right now it is best to wait till it passes. Then you can reset the receiver box by unplugging it for 10 seconds from the power and then allow it to reboot. Also check all the connections in the room with the receiver box from the wall up to the receiver itself. If it does not get off 0 progress of 5, you will need to call Dish network and will probably need a Service Technician Visit scheduled.

Posted on Jan 12, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I disconected my receiver when connecting back did not work never acquire signal


The satellite in cables play a big role in a receiver getting signal. Since they were disconnected, verify the cables are both hand tight and everything is plugged in.

If the satellite was working before, but isn't after disconnecting there may be a connection problem in the line. At that point verify all the cables are tight, and you can also try swapping the Sat In cables around. The Sat In cables have to be in the correct port to work. Let me know if the problem continues!

Tommy Faust
DISH Social Media Representative

May 16, 2012 | DISH Network 322 DTV Receiver

1 Answer

Added a 322 reciever to my lake house to be able to watch tv in 3rd room i had 2 standard recievers before. i installed a dish pro quad lnb & reciever had a separator w/it says dp plus 123254 tuner 2...


Is TV 2 off the 322 receiver being back fed from the receiver or do you have a direct connection to the 3rd room? If it is a direct connection, you would screw the coax from the 3rd bedroom directly to the TV 2 Home Distribution channel 21-69 out port.

If you are back feeding, you need 2 diplexers that connect 1) by the receiver and 2) between the receiver and the 3rd TV. The back feeding will use the same cable coming from the dish to the receiver.

If you have any other questions, please don't hesitate to ask.

Jun 26, 2011 | DISH Network 322 DTV Receiver

1 Answer

Everytime my phone rings my dp311 goes into acquiring signal mode and sometimes stops at progress 2 of 5


Hello, this is Nick Franta with DISH Network Customer Service.

Disconnect the phone line and then unplug the receiver for 10 seconds. Plug the receiver back in and then reconnect the phone line.

Hope this helps.

If you need any further assistance please contact us.

Dec 24, 2010 | DISH Network 311 DTV Receiver

1 Answer

On my 322 DTR I get a Sat 1 no input even when I swap the 2 input cables. Input 2 shows ok


Hello, Daniel Busa here with Dish Network customer service. It sounds like your signal input on your reciever may be fried. You will probably need a replacement, one thing you can try is replacing the separator that runs to the sat input 1-2. This may be the issue as the ports are rated differently if you pick on up make sure it's rated at 2,150 mhz.

Nov 16, 2010 | DISH Network 322 DTV Receiver

1 Answer

Does the dish network 322 receiver require two lines from the satellite to the receiver?


It does require 2 lines form dish unless you have a switch installed such as a dp34 or you have Dish Pro plus LNB"S on your dish and you can use 1 feed to the reciver and use a separator to separate the signal into sat 1 and sat 2 (note: a standard splitter is NOT a separator) a separator is dish brand equipment.

Oct 15, 2009 | DISH Network 322 DTV Receiver

1 Answer

Dish Network - Loss of signal after smart card upgrade.


Hi I will be more than glad to assist you in this concern.. Since you did already all the troubleshooting to fix the problem and according to the customer service, just run the check switch and test, that should fix the problem, but it didnt. The blue card that your refering is the g3 smartcard, it started when u insert to the 301 receiver.. It could be a bad smartcard or the receiver is bad, If you have another solo receiver in the house, just to isolate the problem, try to hook up the other solo receiver in the room where the 301 receiver is hook, run a check switch and test to the other solo receiver, once its done check your sat and signal, once its ok, cancel all the way out and it should acquire the sat signal..it will show attention 015 and let it finish the progress until it download the programming guide.. once u got a picture and the problem still exist with a different receiver. the problem is with the receiver and the receiver needs to be replace, if you call on dish network tech support, tell them that you try using another receiver and install to the room were the 301 is located, so that they wont do a troubleshooting again.. that is.. if you have another receiver to test and isolate the problem, but if not request for a service call so that they will send tech to your house.. please feel free to get in touch.

Sep 04, 2009 | DISH Network 322 DTV Receiver

2 Answers

Have a 322 with a DP 34 switch and have a strange problem. I thought something may have been damaged in a recent storm, TV 2 lost signal entirely and I lost sat 110 on TV 1 leaving me only 119. After some...


bring the 301 receiver to where the 322 is and one at a time hook each satellite in coaxial feeds to it if you get both satellites then the receiver can be the problem if not then the outputs on your dp34 switch can be defective.

Aug 10, 2009 | DISH Network 322 DTV Receiver

2 Answers

TV or control doesn't work need help know


ok my tv is doing the same thing and i need help if you found a solution please email me at pieces41096@aol.com

Jul 06, 2009 | DISH Network 322 DTV Receiver

1 Answer

322 dual tuner-failure to receive signal only to one TV


If you have one cable leading from the wall toward the back of the receiver you can disconnect the seperator and diplexer (if equipped) from the SAT 1 and SAT 2 ports and connect the line from the wall directly to one of the ports and run a check switch test. You should get a 1 of 2-4 depending on lnb type on the tuner you connected the line to and a 1 of 38 on the other. Perform this operation for both SAT 1 AND SAT2 as described above. If you have the 1 of 38 appearing only on the port that the line is not connected to then the receiver is good and the problem may be the seperator which is the silver device that has two wires going to the back of the receiver initally and one port connected to the SAT port of a diplexer. Disconnect the diplexer and hook the seperator to the receiver and run the SAT line from the wall to the single port of the seperator and do a check switch. If you don't get a 1 of 38 it is good and you have a bad diplexer. If your system does not use diplexers and you are experiencing the loss on TV2 you may have a bad TV2port on the receiver. You can take the wire from the TV2 PORT(in home distribution system) and place it on the 3-4 that the TV1 line is run from. Then go to TV2 and put that tv on channel 3 and see if you have picture. If the problem is at TV1 reverse the process by connecting the line on the 3-4 ut to the TV2 port and putting TV1 on chanel 60 or 73 and see if you get picture. if either produces picture on the bad tv the port to that TV is faulty. If you were still unable to get picture it may be a cabling, connector, barrel isssue that requires a tech to visit. Hope this assists you. Thanks for using Fix Ya.

Jan 03, 2009 | DISH Network 322 DTV Receiver

1 Answer

Only half of my 322 receiver is working. I can only acquire signal to one TV.


Make sure u use the other remote to turn it on. Check your LNBF for signal. Make sure your blue light is on, on the receiver itself. You cannot use the green button remote to turn the blue light ON??

Jan 03, 2009 | DISH Network 322 DTV Receiver

Not finding what you are looking for?
DISH Network 322 DTV Receiver Logo

351 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1257 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Are you a DISH Network Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...