Question about Kenmore 82822 Electric Dryer

2 Answers

82822 / 82824 / 82826 Electric Dryer: kenmore HE2 electric dryer, beeps and all display ...

Kenmore HE2 electric dryer beeps and all display lights work but won't come on error display f-01 what does this mean?

Posted by Anonymous on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 15,935 Answers

F01 - There may be an internal problem with the control, attempt a Hard Reset.

Hard Reset - In some cases the control can be non-functioning or may not accept activation from the control panel. To clear and restart the control follow the these steps:

* Unplug or turn the circuit breaker off for 30 seconds.
* Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
* Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.
* Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

The F01 generally indicates a failed electronic machine control board.
This error code can sometimes be caused by a glitch or power surge through the electrical lines.
You may be able to clear this code by unplugging the washer for 5 minutes.
If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.

The procedure for accessing and replacing this control board is shown in this image...

http://media.fotki.com/1_p,wkwdftgtbkdgfrwxgtqsskgwtqkq,vi/ksrttqdqrxkssrqtgsd/1/1303472/5961857/image12917img-or.jpg

Be sure to unplug the washer before accessing internal components.
When you access the control board, I recommend transferring the wires from the old control board to the new replacement control board one connection at a time.
Once you have all of the wires transferred, remove the old control board and mount the new control board in the washer.
Reassemble and test the washer.

The "F01" error code indicates a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU.
The "F01" can also be displayed if the onboard "Pump Driver" fails to activate.
Generally in order to correct this failure will require replacing the CCU.
There is no way to test and verify if the control board has failed.
The technical data sheet basically states to replace the CCU.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 25, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

My kenmore smartpak dryer won't start. It lights up, but I get an error F01 message, what should I do.

Posted on Apr 08, 2012

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Keith Savasten

  • 1 Answer

SOURCE: kenmore he2 electric dryer error code f-01

Per the documentation with the dryer the

Electronic control board


Needs to be replaced.

Posted on Mar 11, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No heat in Kenmore HE2 electric dryer


here is a professional tech's reply to this problem not sure if you want to go to this length or not but maybe.
thought I'd pass on.
https://www.applianceblog.com/mainforums/threads/46396-Kenmore-HE2-electric-dryer-works-but-no-heat
hope this helps a little.

Jan 07, 2018 | Kenmore Dryers

1 Answer

Sears Electric Dryer is flashing F01 What is wrong?


The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.
You can order a new control board from the Sears PartsDirect website.
http://www.searspartsdirect.com/partsdir...
Here's how to do it: http://media.fotki.com/1_p,wkwdftgtbkdgf...


Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Error code on dryer F01 - Kenmore Elite HE3 Dryer - iFixit

https://www.ifixit.com/.../Error+code+on+dryer+F01 Traduire cette page The F01 indicates a failed electronic machine control board. This error code can ... The Kenmore Elite HE3 is 7.2 cu. ft. capacity electric dryer by Kenmore.

Dryer Sears / Kenmore HE3 - F01 Error Code Main Circuit ...

2q==? 7:35 https://www.youtube.com/watch?v=eWqrn5klxm0 20 avr. 2015 - Ajout? par Jim Dandy Sears Kenmore Dryer Model HE3 - F01 Error Code. Main Circuit Board Repair - Electronic Control Board ...

Error code F1 on Kenmore HE2 electric dryer appeared ...

www.shopyourway.com > ... > Questions Traduire cette page Sears Kenmore HE2 electric dryer; model #11087571601. F1 error message appeared ... Power it back up and see if you still get the F01 error code. If not, then I ...

What does the error code F-01 mean on my Kenmore front ...

www.shopyourway.com > ... > Questions Traduire cette page By unplugging and plugging in the electrical cord, I got the dryer to work again. ... What does the error code F-01 mean on my Kenmore front loaded HE2 dryer? ... My kenmore washing machine 110.46462500 is flashing an error code F.01 ...

Feb 04, 2016 | Sears Kenmore Elite Electric Dryer 69278

1 Answer

My Kenmore 6.7 cu ft he2 Super capacity electric dryer is taking twice as long to dry. no error codes


It sounds like a connection problem with one of the heating elements, or perhaps only a clogged input or output hose from the dryer. Either of these could cause the problem...also, a burned out electric element.

Jan 15, 2013 | Kenmore Dryers

1 Answer

Kenmore HE2 dryer will not start


the relay for the motor is probable stuck recommend service

Jun 03, 2010 | Kenmore 82822 Electric Dryer

1 Answer

Kenmore electric dryer 66802 timer goes off all the time


Try unplugging it for ten mins or so to reset the chip.

Mar 25, 2010 | Kenmore 62802 Electric Dryer

2 Answers

Kenmore he2 electric dryer error code f-01


always unplug for 10 minutes and retry first.

Jun 12, 2009 | Kenmore 82822 Electric Dryer

1 Answer

I HAVE A NEW (3 MONTHS) KENMORE HE2 ELECTRIC DRYER MODEL # 110.8756, IT APPEARS THAT I CAN TURN THE POWER ON, SET THE PARAMETERS BUT WHEN I PRESS START I JUST GET A BEEPING SOUND. THE LIGHT ON THE...


because is a 3 month old dryer is better for a technician to give you a diagnostic because can be a manufactory issue.
If you have any question please let me know.
Was this helpful?

Feb 17, 2009 | Kenmore 62602 Electric Dryer

1 Answer

Kenmore HE2 Dryer


That model has a belt switch. If the belt is broken then it will not com on.

Oct 30, 2008 | Kenmore 62602 Electric Dryer

1 Answer

Kenmore dryer HE2


my kenmore he2 gas dryer runs for 2 or 3 minutes the shuts off, flashing an f22 error code

May 05, 2008 | Kenmore 85871 Electric Dryer

Not finding what you are looking for?
Kenmore 82822 Electric Dryer Logo

2,084 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Ned Halaweh
Ned Halaweh

Level 2 Expert

240 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...