Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Washer making loud noise and wont spin

During the spin cycle, heard a banging noise, then it got progressively worse, after a few more loads during teh spin cycle the washer began to make a loud noise like the motor was straning and the tub would not spin anymore.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 343 Answers

Check and see if the inner drum is loose and floppy.if it is, it's likely the bearings have collapsed, and require replacement...If the drum feels stiff and tight, it could be that something is jammed between the inner and outer drums. Both situations could be costly...Get quotes....Good luck...Nomess

Posted on May 22, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Loud banging noise during spin cycle


If you balanced the machine, the only other problem could be the load itself. Either the load is too great or if washing a single item its falling to one side, tilting the drum and when spinning it will thump. Try even lodes.

Jan 31, 2018 | Washing Machines

1 Answer

Loud noise during spin cycle now they are stacked


a loud noise comes when you forget to remove shipping bolts after installation or if the shocks are worn out it makes noise thirdly the bearings might be worn out if the washer is more than 6years old

Jan 21, 2013 | LG Cherry Red Steamwasher Wm2487h Front...

1 Answer

Frigidare front load washer has loud banging on spin cycle. After much work we reallized one shock was broken of which we repaced both now it still making the loud banging shaking motion. Also the washer...


Thanks for choosing FixYa and welcome. Since the suspension is ok and it is level, check your drive motor and spin bearing. Usually, these are the trouble parts when loud noises are associated with the spinning cycle. Your drive motor controls the spinning. Since the noise is during spinning, that is probably where your problem lies.

Apr 29, 2011 | Frigidaire GLTF1670A Front Load Washer

2 Answers

The washer shakes uncontrollably during the spin cycle also a loud banging noise is heard during the spin cycle.....


If front load check the inner drum If it is loose at all you have a lot of problem . Very expensive.

Nov 17, 2010 | GE Washing Machines

1 Answer

During spin cycle washer is making loud noise


If it is making a sound like a loud rumbling sound similar to a jet plane taking off, it probally due to the seal has failed causing water to leak into the bearings. The bearings begin to rust, and no longer round and the noise gets progressively louder. It can be rather expensive to fix. Get a few estimates before deciding whether it is worth fixing.

Aug 30, 2010 | Maytag Neptune MAH6500A Front Load Washer

1 Answer

Loud banging noise during rinse


Most noises from a washing machine occur during the rinse or spin cycle. If you hear loud thumping during the spin, the load of clothes may have become unbalanced. Stop the washer and redistribute the clothes, then re-start it. Repeat these steps if necessary.This will solve your problem.

Apr 08, 2010 | Whirlpool GHW9100L Front Load Washer

1 Answer

My Maytag HAV2557AWW Loud Noise


pull hoses off the pump and see if there is anything stuck in it

Jun 12, 2009 | Maytag HAV2557 Top Load Washer

1 Answer

Kenmore series 80 washer makes loud knocking noise during spin cy


Unless your front loader is set firmly on concrete and leveled to perfection, the force of a heavy wash load spinning in excess of 1000rpm will create a bit of vibration and noise.A firm footing is your best defense against to much movement.
Also due to the earlier movements during the spin cycle, the shocks that are used to dampen the spin cycle might have been broken or damaged.
If the problem persists inspite of proper levelling, please do check for the shocks or might have them replaced them for good.

Dec 14, 2008 | Kenmore 24032\24036 Top Load Washer

1 Answer

Three day old Indesit washing machine


Is it a maytag? My maytag front load washing machine had 2 long bolts with plastic braces on them, to keep the drum still during shipping. Mine would bang and shake all over. I got the book out before I finally figured it out. I had to take the back cover off and remove the bolts and plastic braces over them. They look like they' 8 inches long or so. It works great now.

Carolynn

Jul 15, 2008 | Indesit W 123 Front Load Washer

1 Answer

Loud Noise during spin cycle


drum bearings are gone,it would cost too much to repair,the drum shaft would to be repalced as well.Sorry

Dec 15, 2007 | Whirlpool Duet GHW9150P Front Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

789 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

jimorris77

Level 3 Expert

411 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...