Question about Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Blinking clean light

I have a constant blinking "clean" light on the dishwasher and the dishwasher will not start.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 949 Answers

Hi,

This blinking indicates a failure to properly heat the water, the link below will have instructions on how to reset the control so you can use the dishwasher and it will provide areas to look as to why it failed. Let me know if it was helpful.

Blinking Clean light

Posted on May 23, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kid 60 s10 please give fault codes


Hi Roger, Hope this helps......CHEERS..

KENMORE DISHWASHER ERROR CODES

Kenmore Dishwasher Error Code = Start Resume light blinking slow
When the dishwasher door opens or electrical power is removed during the cycle then the dishwasher will not start again. The door is detected as being closed and the Start Resume button is being pressed
Kenmore Dishwasher Error Code = Clean light is blinking 7 times
Heater circuit fail. Control panel did not detect the water getting hot. Did not detect heating element was energized to heat the water during the wash cycle
Kenmore Dishwasher Error Code = Sanitize LED blinking at end of cycle
Control panel could not detect if sanitation has been achieved
Kenmore Dishwasher Error Code = Console light blinking rapidly
There is a stuck button on the control panel
Kenmore Dishwasher Error Code = Clean light is constantly illuminated
Dishwasher cannot start a wash cycle until it sees that the door has been opened after the previous washing cycle
Kenmore Dishwasher Error Code = Control lock LED is ON but not responding to pressing of the keys
Turned on by accident or there is a control detected key pad problem

Mar 31, 2016 | Kenmore Dishwashers

1 Answer

Dishwasher clean light blinks constantly, can't get washer to start up and wash. Buttons will light up but it wont start.


Hello, Thank You for using FixYa. I will be helping you today.Try pressing heated dry,Normal,Heated dry,Normal and all lights should come on if they do wait like 5 seconds and hit cancel and see if the unit will start. If this happens again it may be a heating issue.
Thank You and please rate my answer if it was helpful..

Jun 22, 2011 | KitchenAid Dishwashers

1 Answer

My dishwasher blinks the green clean light


May have a bad heater. press hi temp, air dry,hi temp, air dry (or whatever button is equivalent on your model). this starts a test and will allow unit to work again. When drying light goes out touch the heater. If it is cold then it may be bad. You will need a voltmeter to tell for sure however.

May 27, 2010 | Whirlpool 24 in. GU2548XTP Built-in...

1 Answer

Constant flashing clean light


count the blinks shoud be 7 times it blinks then a pause if it does that its a heat circute problem need to check the heater and replace the controls

Jul 13, 2009 | Whirlpool Dishwashers

1 Answer

The start light just blinks and the dishwasher wont start?


just found a web site that says crack door open, press normal, hot dry, normal, hot dry, then cancel to reset the controls.

Mar 12, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Clean light blinks constantly



press heated dry
press normal wash
press heated dry again
press normal wash again..........
.....wait a few seconds
all the lights should come on
press cancel (should hear pump)
hit cancel again

Hope this helps, it worked for me, but it may depend on your model.

Feb 05, 2009 | Kenmore Dishwashers

1 Answer

Dishwasher Clean light blinks constantly.


Try turning off the power to the dishwasher at the circuit breaker box. leave the power off for 5 10 mins and then turn breaker back on and try to restart dishwasher. This may reset the board and it may work

Feb 05, 2009 | Kenmore 16602 / 16604 / 16609 Built-in...

1 Answer

I have the kitchenaid dishwasher model #kudv03ctss0.the clean light stay blinking and when i hit the start it just blinks and then stops but the clean light stay blinking constantly.if i hit the cancel...


Dear friend,
ngfam at you service! happy to assist!


It's an electronic problem!
The lights are called codes and need to be diagnoed by a factory service person!!

We sell appliances for 65 years and I recommend this nation wide Factory repair service!

Call A&E Factory Service /They service nation wide
And are available 24/7 for making appointments!

If the appliance is 10 years old or more,it may make sense not to invest any money to fix it!

Happy to assist you,
PLEASE GIVE ME A GOOD RATING BEFORE YOU SIGN OFF!

Aug 29, 2008 | Dishwashers

Not finding what you are looking for?
Whirlpool GU2400XTP Built-in Dishwasher Logo

972 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike

Level 3 Expert

4369 Answers

Bruce Denton

Level 2 Expert

273 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...