Question about Cisco Catalyst 4006 Chassis ( 4006)

1 Answer

How to reboot a cisco router? - Cisco Catalyst 4006 Chassis ( 4006)

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 79 Answers

From the privileged mode that is the # prompt type reload it will reload the router.

Router# reload

Please save your configuration otherwise it will be lost. Use the following command to save your running configuration.

Router# copy running-config startup-config

Posted on Jun 19, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to retrieve Cisco router password without losing configuration?


You can't, otherwise there would be no point in having a password would there!

Dec 24, 2016 | Cisco Computers & Internet

1 Answer

Cisco AM10 Error "Invalid Key Manual"


Try to reboot and install it again after delete the router setup from device manger..

Feb 13, 2013 | Computers & Internet

1 Answer

We lost power for a few hours .The cable company ( charter ) had to reboot the modem to reestablish the internet connection. Since then I cannot get the Cisco router to work.. I've done all the plug,...


1. if the power went out and then back on it is possibly due to a "power surge" and it possibly damaged the power supply to the Cisco router and or to the router itself.
2. check the routers power supply and replacement is needed if the router was not plugged into a surge protected socket.

Jul 15, 2011 | Computers & Internet

1 Answer

1840 cisco router is not booting only cursor blinking not going ahead


HI,
It May be the problem with the IOS in the router Flash
  • Try hard reboot of the router If it is not soled proceed next.
  • while the router reboot press Pause button continuously, it will enter into the ROMMON mode.
  • using the Xmodem option upload the correct IOS, for refer Please refer the link
  • Please check the configuration Loading by confreg or config-register command and change into confreg 0x2142 to load from the Flash and reboot the router.

Jan 20, 2011 | Cisco (1841) Router (cisco1841)

1 Answer

Password Recovery for Cisco Catalyst 4506


Please see Cisco's page at http://www.cisco.com/en/US/products/hw/routers/ps5199/products_password_recovery09186a0080093e12.shtml
for step by step details and more in depth instruction.

1. Reboot
2. Press the "break" button on your keyboard within 60 seconds of the power-up to put the router into ROMMON mode.
3. confreg 0x2142
4. reset
5. type, "no" when prompted to enter the initial configuration dialog.
6. enable
7. copy startup-config running-config
8. conf t
9. enable secret <password>
11. config-register 0x2102
12. reboot again

Jan 20, 2010 | Cisco Catalyst 4506-E Cat4500 E-series...

4 Answers

Can not login on con 0 port (not text), lost


default username and password for all router are

admin and admin

or

admin and password

try these two combinations

else try link

http://www.cisco.com/en/US/products/ps6187/index.html

Oct 03, 2009 | Cisco 1811 Router

1 Answer

Cisco 1811 router freez


replace your router, got a problem with the board...

Jun 18, 2009 | Cisco 1811 Router

1 Answer

Unable to connect 2 routers need help!


Hi,

Do you have any funky subnets for your Cisco router? Do not connect the wireless router to your network yet, as it may have the same IP address as your other router.

Basically the easiest way to do this is to set a dedicated IP for the 2Wire router on the Cisoo router. Then make them stay on the same subnet, but give an IP range for your Cisco router, like 1-50 or something. If you give the 2Wire router IP .51 for instance, then give the Wifi users on the 2Wire IP range from .52-75 or something.

Make the 2Wire router only use wifi and not serve DHCP addresses. Then you setup the 2Wire router to get its info from the Cisco router.

I searched and there is no howto out there for doing this with a Cisco router. However, here is one I used to setup a similar scenario with a Netgear router. It worked. If you are able to translate a bit, it might work for you:

http://kbserver.netgear.com/inquira/default.asp?ui_mode=answer&prior_transaction_id=306896&action_code=5&highlight_info=16778323,235,239&turl=http%3A%2F%2Fkbserver.netgear.com%2Fkb_web_files%2Fn101236.asp&answer_id=6056802#__highlight

Here is another article:
http://kbserver.netgear.com/inquira/default.asp?ui_mode=answer&prior_transaction_id=306896&action_code=5&highlight_info=16777285,246,260&turl=http%3A%2F%2Fkbserver.netgear.com%2Fkb_web_files%2FN101496.asp&answer_id=6056800#__highlight

Let me know if you are able to work through this. You need to give the 2wire router a static IP and you need to NOT use it for wired connections, and not use it to serve DHCP settings.

Jan 21, 2009 | 2wire 2700HG-B Router (2700HGB)

1 Answer

Cisco 857 router


You might need to reset the password. In order to do this, follow these directions:

  1. Console into the router, then power cycle it. As its rebooting hit the "break | pause" button on your keyboard, and you get to the rommon1> prompt.
  2. Then type rommon1>confreg 2142 rommon2>reset
  3. The router comes back on as if it were new---answer no to the first question, and sometimes it asks a second question (do you want to terminate autoinstall, or something...)---answer yes to the secondquestion if it asks. Then hit enter and you get router> in a few seconds.
  4. Then router>en router#copy start run

create a new account:
  1. router#conf t
  2. router(config)#username bob priv 15 password bob
set register back:
  1. router(config)#confreg 0x2102
  2. router(config)#exit
  3. router#wr
  4. router#reboot

and that should let you login with bob/bob

Nov 30, 2008 | Computers & Internet

Not finding what you are looking for?
Cisco Catalyst 4006 Chassis ( 4006) Logo

Related Topics:

817 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...