Question about Linksys BEFSX41 Router (DHBEFSX41)

2 Answers

I have problem connecting new computer to befsx41

I have a problem connecting new computer to befsx41 port. The port LED's are slowly flashing but I don't have link status on the computer's network card.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,851 Answers

Where are you with this ?

Posted on Jul 03, 2010

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,768 Answers

1.Unplug the router for 1 minute then plug it back into the AC . Wait........ 30 second to see if you have acquired a signal
2. Confirmed that you have connectivity with the ISP ( internet service provider)
a.Check your wireless setup and see if the wireless is on.
b. do ipconfig / all
c. test the router by setting up the router by MAC address..

Posted on Jun 19, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to know how I can re-set my 3Com 3crwe955275 wireless access point to its default factory settings. Can anyone help?


1 Remove power from the Gateway. 2 Disconnect all your computers and the cable/DSL modem from the Gateway router. 3 Using a straight through Ethernet cable, connect the Ethernet Cable/DSL port on the rear of the Gateway to any one of the LAN ports. 4 Re-apply power to the Gateway. The Alert LED will flash as the Gateway starts up, and after approximately 30 seconds will start to flash more slowly (typically 2 seconds on, 2 seconds off). Once the Alert LED has started to flash slowly, remove power from the Gateway. 5 Remove the cable connecting the Cable/DSL port to the LAN port, and reconnect one of your computers to one of the Gateway LAN ports. 6 Re-apply power to the Gateway, and when the start-up sequence has completed, browse to: http://192.168.1.1 and run the configuration wizard. You may need to restart your computer before you attempt this. 7 When the configuration wizard has completed, you may reconnect your network as it was before

Here on page 85 of the manual
3Com 3CRWE53172 User Manual Forgotten Password And Reset To Factory...

Feb 18, 2015 | 3Com Computers & Internet

2 Answers

WHAT LIGHTS ON LINKSYS ARE SUPPOSED TO BE BLINKING


Note that incoming traffic will cause the WAN (or Internet) light to blink even if it is 'probe' traffic trying to break in to your network. Such traffic is to be expected and is the reason you have firewall functionality in your gateway router.

On the inside, there is a bit of traffic on any LAN when the computers are turned on. Messages generated by the router itself are used to find computers and printers for a lot of different legitimate reasons.

Feb 25, 2013 | Linksys Wireless-G WRT54G Router

1 Answer

I HAVE A GAMEWARE PS3 CONTROLLER BUT HAVE LOST THE INSTRUCTIONS HOW TO ASSIGN TO PS3. PLEASE ADVISE


  1. turn on PS3
  2. Press HOME on GamePad - 4 channel indicators flashing slowly
  3. Press FC on Gamepad - 4 channel indicators flashing quickly
  4. Plug the receiver into the USB port on PS3 - 4 channel indicators flshing slowly
  5. Press HOME on Gamepad, one active channel LED indicator will light up

Jan 08, 2011 | Cameras

1 Answer

I have a type c wireless controller how to connect it to the ps3 it dont indacate


From the Manual:
1. With your Playstation 3 game Console on and the ON/OFF switch on the bottom of the controller set to on. Plug in the USB receiver into a USB port in the Playstation 3. The LED will flash slowly.
2. Press the "connect" button on the receiver. The LED will flash rapidly.
3. Press the "menu" button on the controller. The four channel lights will flash rapidly until the sync process is done. When the sync process is done one of the channel lights will remain solidly lit.
The manual can be found here in PDF format. http://assets.dreamgear.net/manuals/DGPS3-1324.pdf

Jan 07, 2011 | DreamGear TYPE 6 2.4 GHz Wireless...

1 Answer

No wireless connection for laptop. Linksys router - model #wrt160n v2


you can run a direct line to that router and go to the cisco web site and get the information you need to run that router. its a pdf format and is 2.56 Meg. Try this

SecureEasySetup (Orange/White) The Cisco logo is the Router's SecureEasySetup button. It

lights up and will stay orange when the Router is powered on. The color orange indicates that

the Router is not using the SecureEasySetup feature, while the color white indicates that the

Router is using the SecureEasySetup feature. When the Router enters SecureEasySetup

mode, the Cisco logo will turn white and start flashing. After the Router has generated

the SSID and WPA Personal key, the Cisco logo will stop flashing and stay white.

To clear the SSID and WPA Personal key, press and hold down the Cisco logo for five seconds.

The Cisco logo will flash slowly as the Router resets itself. The Cisco logo will turn orange to

indicate a successful reset.NOTE: SecureEasySetup is a feature that makes

it easy to set up your wireless network. If you have SecureEasySetup devices, run the Router's

Setup Wizard CD-ROM and follow the onscreen instructions to use SecureEasySetup.

Power (Green) The Power LED lights up and will stay on while the Router is powered

on. When the Router goes through its selfdiagnostic mode during every boot-up, this

LED will flash. When the diagnostic is complete, the LED will be solidly lit.

DMZ (Green) The DMZ LED indicates when the DMZ function is being used. This LED will

remain lit as long as DMZ is enabled. WLAN (Green) The WLAN LED lights up when

the wireless feature is enabled. If the LED is flashing, the Router is actively sending or

receiving data over the network. 1, 2, 3, 4 (Green) These numbered LEDs, corresponding with the numbered ports on the Router's back panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected to a device through that port. A flashing LED indicates network activity over that port.

Internet (Green) The Internet LED lights up when there is a connection made through the

Internet port. A flashing LED indicates network activity over the Internet port.

Good luck

Nov 26, 2010 | Computers & Internet

1 Answer

I have a befsx41 router that doesnt say any versiion on it.. i have two computers i want to use through it but only one will connect at a time when i use the router what could the solution be?


so you said that only one is able to go online at a time .
that means the rotuer is not working properly or the connections are not done properly.
Who is your internet service provider ?
make sure that the modem is connected to the internet port on the router and the computer will be on port 1,2,3,4 ( any one of them).
If the connections are proper and you are able to go online on only 1 computer at a time then check the IP address on the working computer.
You should get the private IP address like 192.168.x.x. X ( might be any number).
If you get public IP address then the router is not working now.
You can not even upgrade the firmware of the router. Because the router is now working as a switch.
Click Here for step by step solution

Oct 30, 2009 | Linksys BEFSX41 Router (DHBEFSX41)

1 Answer

How do I configure a BEFSX41 to be an access point (router only)? I've given up on using it to access the internet due to connection problems. I switched my Belkin 54G from an access point to the main...


If you have a modem and a router the two needs to have seperate Ip address. For exmaple I have a westell 6100 G modem with a wrt54g speedbooster router. I have my modem local ip set at 192.168.1.1 and my router local ip set at 192.168.9.1. I got my router on to do the dchp starting address with 192.168.9.15. Plug your cable from the modem into the wan port of the router and it sould work.

Oct 04, 2009 | Linksys EtherFast BEFSX41 Cable/DSL...

4 Answers

We have a wireless keyboard and mouse and it seems that something between them and the computer is slow or off. we type and only a few letters appear..the mouse seems to be ok just kinda slow ofrom when...


Most likely you need to re-sync the device

  1. Resynchronizing the keyboard and/or mouse causes the devices to reconnect to the receiver using new identification numbers. Use the following steps to resync the devices:
    NOTE: The following connection sequence must be completed within 60 seconds. If the sequence is not done in 60 seconds, start over.
    1. With the receiver plugged in, press and hold the Connect button on the receiver until the activity LED flashes.
      NOTE: Some HP computers have receivers built into the front of the computer; such as TouchSmart 700 Series PCs and Digital Entertainment Centers. Look for a small connect button built into the case. If you have a TouchSmart 500 or 800 Series PC, the receiver plugs into a USB port on the underside of the case and does not have a connect button - skip this step. Figure 4: An example of a receiver c01065862.jpg 1 - Connect button and LED activity light Figure 5: Another example of a receiver c00526313.jpg 1 - Connect button 2 - Num Lock LED 3 - Alpha Lock LED 4 - Scroll Lock LED 5 - Activity LED
    2. Press and hold the recessed connect button on the underside of the keyboard until the activity light on the receiver stops flashing. When you release the button, make sure it does not stick in the depressed position.
      NOTE: If problems persist after resetting AND there is another wireless keyboard or mouse near, use these steps again, holding down the keyboard or mouse button for ten seconds. Doing so may give the keyboard or mouse a new ID number in case the other keyboard or mouse was using the same number.
    3. Press the Connect button on the receiver again until the activity light flashes.
    4. Press and hold the recessed button on the underside of the mouse until the activity light on the receiver stops flashing. Make sure the connect button does not stick in the depressed position.
  2. If your mouse and keyboard have a USB receiver, unplug the USB receiver, wait 10 seconds, and then insert into another USB port - preferably into a USB port that is closer to the mouse and keyboard. For example, if the USB receiver was plugged into a USB port on the back of the computer, unplug it and plug it into a front USB port.

Hope this helps!! Good luck!!

Sep 17, 2009 | HP Wireless Optical Mouse

3 Answers

How to set up yobo controllers for ps3


I just bought a used one today and took me a little while to get it to work. Plug the USB receiver in and turn on the PS3. Press the Mode button and the lights will flash repeatedly at a fast rate (it's searching for the receiver). When it finds the USB receiver, the lights will still flash, but slower than before. When they're doing this, press the mode button again, and that should be all that you have to do. You can also plug the receiver in USB slot one, the charge cable in slot 2, and do the steps to set it up to make it work while charging. (I tried taking the receiver out while charging, and the lights started flashing again so I guess the USB receiver has to be in at all times)

Jan 11, 2009 | YOBO FC Game Console

1 Answer

Router/playstation 3


I reckon that you may need to configure your router to open ports to allow the internet traffic access. If you go to this link it will help you to configure the necessay "Port Forwarding" settings. http://portforward.com/english/routers/port_triggering/Linksys/BEFSX41/BEFSX41index.htm Are you connecting with a wired or wireless setup? Hope this helps - let me know if it does not

Sep 22, 2007 | Linksys BEFSX41 Router (DHBEFSX41)

Not finding what you are looking for?
Linksys BEFSX41 Router (DHBEFSX41) Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...