Question about Dell OptiPlex GX110 PC Desktop

Open Question

Error showing plug and play configuration error

Error showing plug and play configuration error alert the cover was previousley removed checkpoint [cnic]

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
sandrew

andrew pester

  • 2961 Answers

SOURCE: Plug & Play Configuration Error

this may not be your ethernet card that is causing the fault, it is probably a flat cmos battery (CR2032) disc shaped battery normally close to the memory slots. This will need to be replaced, it's a simple job, just remove side panel of tower and flip the battery out and replace, probably cost $3.00. You will then be prompted on the next boot up to press f2 to set the date and time and then save and exit again for a reboot

Posted on May 29, 2007

Ad

Curtis Richner

  • 461 Answers

SOURCE: Dell Desktop Plug & Play Configuration and Keyboard Error

My first thought is a damaged port. Check all the ports that were connected for bent pins and straighten if possible, but be careful and be sure the system is off and unplugged from the AC power. Also check for loose cards or cables that may have happened in the transport.

Posted on Dec 17, 2008

acdr

kishor khatri

  • 1913 Answers

SOURCE: plug and play configuration error

reconnect all cables device to cpu .remove usb device if ther eis connect then asfter loading the operting system connect again.

Posted on Jan 29, 2009

Gyanendra Kumar

  • 479 Answers

SOURCE: plug and play configuration error

go in bios then checked wether plug and play support is enabled or not? enable it and this should work.

Posted on Jan 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plug play configuration error


What hardware have you added? What is the Configuration error? Why don't you ask a question?

Aug 21, 2013 | Dell Dimension 8200 PC Desktop

1 Answer

Plug & Play Configuration Error


restart your computer repeatedly tapping the f8 key to enter safe mode while the screen is black once in safe mode where the only things working will be your keyboard and mouse allowing you to attempt to repair your computer

you could select the option start at last known configuration that worked this will tell you if and what file has been corrupted or missing then you will know if its a hardware issue
hope this helps

Nov 30, 2011 | Dell Dimension 8200 PC Desktop

1 Answer

Can only take 5 second videos and alert shows on screen...


I had the same problem. Casio states in the manual that the camera is overheated. But this could not be true in my case, because the error appeared right after switching on the camera.
I found it must be a software error. After reseting the menu settings to default in the setup menu, all was fine again.

Jun 01, 2009 | Casio Exilim EX-Z77 Digital Camera

1 Answer

"plug and play configuarataion error"


The BIOS was unable to configure bus-resource. There may be an interrupt conflict which can't be avoided. Dell suggests that you remove some of your non-essential cards and see if it goes away. In one case this problem was due to a defective motherboard. I also heard that some try unplugging things like your speakers, mouse, keyboard...ect.. and plug them back in.

Apr 04, 2009 | Dell Optiplex GX110 (2909T) Motherboard

2 Answers

Plug and play configuration error


reconnect all cables device to cpu .remove usb device if ther eis connect then asfter loading the operting system connect again.

Jan 29, 2009 | Dell Dimension 4500S PC Desktop

1 Answer

Dell Desktop Plug & Play Configuration and Keyboard Error


My first thought is a damaged port. Check all the ports that were connected for bent pins and straighten if possible, but be careful and be sure the system is off and unplugged from the AC power. Also check for loose cards or cables that may have happened in the transport.

Dec 17, 2008 | Dell Dimension 4600 PC Desktop

2 Answers

I installed 4gb of memory 4x1GB 240 pin and when booting up the computer recieved the decomplilation or disassembly prohibited.  What do I do?


HI there,

If you have installed the memory module correctly and are the right ones, than go into your bois and in there should be overwrite o clear this message.

Its only an alert message when you pc has been opened.

Regards,

Philip

Dec 06, 2008 | Dell Optiplex GX280 (99301) Motherboard

1 Answer

Ps3 error 80028f17


Error code 80028F17 can mean two things:

Either

1. "Ps2 disc Boot Error , An error occurred during the start operation; Ps2 game swapped using the eject function and then play pressed quickly - Backup ps2 game inserted again". From here.

Or

2. Happens when you try to play "C&C - Red Alert Retaliation" for PS3 from the PlayStation Store. See here for more information.

Sep 03, 2008 | Video Game Consoles & Games

1 Answer

Audible alert


Run Array Configuration utility from your SmartStart disc. If the array is degrades the system will show to you.

Nov 07, 2007 | HP Compaq ProLiant DL380 G4 Server

Not finding what you are looking for?
Dell OptiPlex GX110 PC Desktop Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Alun Cox

Level 3 Expert

2679 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a Dell Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...