Question about Sharp AR-C160 Color Copier

1 Answer

Copier problem - service code F1-70

When I turn on power I get a call for service code F1-70

Posted by on

  • jean claude liloli Nov 15, 2011

    ma machine sharp ar c150 digital me donne un code f1-70, que dois-je faire pour enlever ce code

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 54 Answers

F1-70 is communication trouble between the machine and the sorter finisher. Check the cables connecting the copier and the finisher and power off and on machine. Should clear the code. If problem persists, may need a new board.

I would also check the ground between the copier and finisher.

Don't forget to rate your answers, please!

Posted on Jun 08, 2008

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi can anyone help correct error code E7 10 on asharp AR 5516S copier


It's one of those dealler faults..

"Turn off the power switch, wait about 10 seconds, and then turn on
the switch again. If this does not clear the message, write down
the code (Main code and sub code exists.) that appears and then
unplug the power cord and contact your authorised service
representative. Tell your authorised service representative what
code appeared and the circumstances under which it appeared."

from the following link..
https://www.manualslib.com/manual/601912/Sharp-Ar-5516.html?page=74#manual

Feb 26, 2017 | Office Equipment & Supplies

Tip

How to resolve Cannon ir400 Error e004


<span>Hi,<br /><br />For error code E004-001 or E004-002<br /><br />Cause:<br />The SSR has a short circuit.<br />&bull; The SSR has an error.<br />&bull; The DC controller PCB has a fault.<br />The heater relay has an error.<br />&bull; The heater relay has an error.<br />&bull; The DC controller PCB has a fault.<br /><br />Description:<br />&bull; The fixing heater remains<br />on.<br />&bull; The fixing temperature has<br />increased abnormally.<br />The heater relay remains on.<br /><br />FIRST TRY TO CLEAR ERROR:<br />Resetting Errors<br />1. The following error codes cannot be reset by merely turning off and then on the main power.<br />They require resetting in service mode:<br />E000, E001, E002, E003, E004, E032, E717<br />1) Start service mode, and select COPIER&gt;FUNCTION&gt;CLEAR&gt;ERR.<br />2) Press the OK key.<br />3) Turn off and then on the main power.<br />2. Error codes other than the above may be reset by turning off and then on the main power.<br />n Detail Code<br />Some error codes offer detail codes, which may be checked in service mode:<br />COPIER&gt;DISPLAY&gt;ERR (3rd block from the right)<br /><br />SERVICE MODE: <br />1) Press the asterisk key ' * ' on the control panel.<br />2) Press '2' and '8' on the keypad at the same time.<br />3) Press the asterisk key ' * ' on the control panel.<br /><br /><br />If these doesnt helps, you need to call service to locate the fault, which is probably bad thermistor.<br /><br />Hope that helps!<br /></span>

on Feb 06, 2011 | Cannon i70 Printer

1 Answer

Need the service code to enter service mode.


How to set up the service mode:
Service mode:
1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select "Features".
4. Select "Current Software Info".
5. Press [0], [6], [2], [5], [9], [6] and [Info] buttons on
the remote control unit in this order. The following
screen appears.
Code :
Pic code :
M I P S :
Press "POWER" key to exit.
*******-***-*-*****-****
**-*******-*****-**
Push 0key
Tuner :
S a f e t y :
****-*****-****
safety_Non

Dec 11, 2013 | Canon NP 6035 Copier

1 Answer

Ihave canon 400 problems. e051, e901, e805 problems frequently please suggest me


Hello,
by the look at your problems:

E051 - Horizontal registration sensor problems
E001 - Fixing temperature faulty
E805 - The Fan rotation problems

It can be that You have problems with DC contoller ( main pcb ) or the copier is in worst condition and there are faults on every segment.

For E001, you can try to reset error:

1. The following error codes cannot be reset by merely turning off and then on the main power.
They require resetting in service mode:
E000, E001, E002, E003, E004, E032, E717
1) Start service mode, and select COPIER>FUNCTION>CLEAR>ERR.
2) Press the OK key.
3) Turn off and then on the main power.
2. Error codes other than the above may be reset by turning off and then on the main power.
n Detail Code
Some error codes offer detail codes, which may be checked in service mode:
COPIER>DISPLAY>ERR (3rd block from the right)



BUT I THINK THAT THE BEST SOLUTION IS TO CALL SERVICE TO RECTIFY THE PROBLEM OR YOU BUY NEW MACHINE:..

Hope that helps!

Jul 22, 2011 | Canon imageRUNNER 400S Copier

1 Answer

Error code appear my Canon Xerox 405 e.i. e002. Please reply me how to solve the problem step by step. Please reply as early as possible. Thanks, Rajes Acharya


Hello,
The following error codes cannot be reset by merely turning off and then on the main power.
They require resetting in service mode:
E000, E001, E002, E003, E004, E032, E717
1) Start service mode, and select COPIER>FUNCTION>CLEAR>ERR.
2) Press the OK key.
3) Turn off and then on the main power.
2. Error codes other than the above may be reset by turning off and then on the main power.
n Detail Code
Some error codes offer detail codes, which may be checked in service mode:
COPIER>DISPLAY>ERR (3rd block from the right


To enter the service mode:

1) Press the asterisk key ' ' on the control panel.
2) Press '2' and '8' on the keypad at the same time.
3) Press the asterisk key ' ' on the control panel

Hope that helps!

PS If not you have problem in fixing unit, probably the fixing thermistor and need to be replaced.

Jun 24, 2011 | Canon imageRUNNER 400S Copier

1 Answer

Service light is blinking & code 06 EC flashes on Sub Zero 650


Turned the breaker off to the fridge for 15 minutes and turned it back on.

Jan 01, 2010 | Sub-Zero 650 / O Bottom Freezer...

1 Answer

System error E000 how do I fix it. I tried what it said in the instructions to turn it off for a while then turn it back on that didn't help. Canon NP6025 copy machine.


To delay the 3 second shut down and enable the technician to access service mode; open the front door and pull out the transport unit. Do not actuate front door microswitch. Press the service mode button, enter " * 4 * ", scroll to error clear and clear error code. Machine will automatically turn off power after clear. Power up machine and test.
If the power shuts down after error code has been cleared, the cause of the error has not been corrected. Correct cause of error code and clear error in service mode.

May 07, 2009 | Canon Office Equipment & Supplies

1 Answer

Service Code Error 486


Please contact your local service representative or original point of purchase for help.
The Service Call indicator looking like a spanner or wrench: char_ric20.gif shows that an error requiring inspection by service representative has occurred in the device.
If the problem is a sensor malfunction, you may be able to solve it and turn the indicator off using one of the following methods.
  • Turn the main power of the device off and on again.
  • If some parts or supplies were replaced recently, try removing them, replacing them again, and then turning the main power of the device on off and on. (If the device is interpreting imperfect parts detection as an error.)
  • The device might be interpreting extreme changes in temperature as an error. Turn off the main power switch, wait for a few minutes to cool it off, and then turn it on.
    Note:
    • If a fax is being sent or received, or printer data is being received, turning the main power of the device off may result in data loss. Ensure that the device is not being used for faxing or printing before you try turning the main power of the device off.
Note that "main power" means the actual, physical power switch.

You may find answers here:
http://www.ricoh.co.uk/KBase/KBLink.cfm?ProductUID=2496

Please remember to rate all users who assist you for free :)


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Oct 01, 2008 | Ricoh Aficio CL3500N Laser Printer

1 Answer

After power outage we get a service code


The service code is probably "loss of Power" error.
One thing you might try is getting a battery back up that is rated for a copier machine.
This way if the power goes out the battery back up would keep power going to the machine preventing the error code.
FYI... the battery back ups are NOT made for copiers. You need on that is rated to back up a regular copy machine.

Hope this helps a bit.
Good luck.
Have a good day.
Mac =)

Apr 04, 2008 | Canon imageRUNNER 5570 Copier

2 Answers

5020i error code E000001-0000


turn on the copier and quickly press * (with the little head around it) then 2 and 8 at the same time, then the * again... this should put you in service mode. now press copier >funtcion>clear>err>ok. now turn the copier off and back on, If the code comes back call your service local service tech.

Jan 08, 2008 | Canon imageRUNNER 5020 Copier

Not finding what you are looking for?
Sharp AR-C160 Color Copier Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Office Equipment & Supplies Experts

Anthony Karuku

Level 2 Expert

268 Answers

amir hamza
amir hamza

Level 2 Expert

318 Answers

Tareq Bin Mostaq...
Tareq Bin Mostaq...

Level 3 Expert

1449 Answers

Are you a Sharp Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...