Question about Canon PIXMA MP810 All-In-One InkJet Printer

3 Answers

Cd tray error Canon Pixma MP810

Some one else wrote:
My ip3000 cannon printer keeps coming up with an error when I try to print CDs. It say the inside try is open and I should remove the CD try, close the tray and press resume, problem is I want to print the CD on the tray!

I have the same problem with the Canon Pixma MP810. I put the CD tray in the front feed, change location to down below, and it gives an error that reads:
"inner cover open, close inner cover" which is how the cd tray fits in. If I close it then the cd tray will not feed. I am under a deadline, a super quick answer would be fantastic.

Posted by on

  • 1 more comment 
  • Anonymous May 20, 2008

    I have the same problem with the Canon Pixma MP810. I put the CD tray in the front feed, change location to down below, and it gives an error that reads: 
    "inner cover open, close inner cover" which is how the cd tray fits in. If I close it then the cd tray will not feed. I am under a deadline, a super quick answer would be fantastic.



  • Anonymous Jul 15, 2008

    MP 810 - install the cd tray and attempt to print.  The printer then advises that there is no tray inserted... any suggestions

  • Glenda Shepherd
    Glenda Shepherd Nov 08, 2013

    Press print remove tray close cover press OK

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I solved this problem. When you get the message close the cover. (You must press print to get to this stage.) Remove the tray. Close the cover. Press OK. Then wait a few seconds for a dialogue box to appear. It tells you to open the cover and insert the tray and press OK. The tray is taken past the white arrow automatically and prints beautifully. If you are printing more discs immediately do,leave the tray out with cover open, press print and it just works perfectly without any problems

Posted on Nov 08, 2013

  • Glenda Shepherd
    Glenda Shepherd Nov 08, 2013

    I solved this problem. When you get the message close the cover. (You must press print to get to this stage.) Remove the tray. Close the cover. Press OK. Then wait a few seconds for a dialogue box to appear. It tells you to open the cover and insert the tray and press
    OK. The tray is taken past the white arrow automatically and prints beautifully. If you are printing more discs immediately do,leave the tray out with cover open, press print and it just works perfectly without any problems

×

Ad

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

I have tried to print on CD's on my Canon MP810 and although all the settings are correct, i.e. Disk Tray F, etc the diagram on the printer review does not change to the shape of a CD and when I print it prints as though on a sheet of A4 paper. Any suggestions????

Posted on Jan 11, 2010

Ad

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sorry a little late only just read your problem.
The location is not the bottom tray feeder but the disk tray. In settings change your media type to "Printable Disk" the paper scource should automatically change to "Disk Tray" and hopefully every thing will work OK.

Posted on Jul 11, 2008

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why cannon ip3000 can't print in only black and white although I choose grey scale priting?


Not sure of the QUESTION..? Do you want to print colour or black and
white..? Anyway,try this, bring up image , at top left click on Fix , at top
right click on Auto Adjust then go down to Adjust Colour click on and
hold Saturation Slider move to left to remove colour ,right to add colour
go to print and it should give you a black / white image. Remember to
return image back to original colour or image will return to file in b/w
hope this works for you..goodluck...T.C.

Mar 31, 2013 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

I just purchased a ip3000 in an open box type sale. All the seals still in place. New print head in sealed bag. no AC cord and no #6 ink tanks. I already have a ip3000 that works. I attach USB2 cord and AC...


Some possible solutions:

Disconnect and reconnect the USB cable to ensure a secure connection

Press the POWER button to power on the printer

Select the correct port setting (Windows)

Set printer from Offline to Online

Set the default printer (Windows)
Try a different data cable

I have bolded the most likely problems. You did not specify your Operating System so it would be lengthy to describe how to check all of these. For detailed assistance , go to this webpage. In the Please Enter Your Question box, type ' Error: Off-line"; from the menu that opens you can access illustrated instructions for each of the above if necessary.

Trust this helps resolve your problem. Please vote.

.

Dec 30, 2010 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

Cannon PIXMA iP3000 (Waste ink absorber full)


The waste ink absorber is a pair of pads at the edges of the ink carriage path near the bottom of the printer. Canon will sell you a new set to replace them if you want to d-i-y. Alternatively, you can just rinse the pads until the water runs clean once you open up the printer. Dry the pads well before reinstalling. You need to take the printer apart from the top and get under the ink carriage.

Once you reinstall the pads, you can reset the counter by:
Pixma IP3000
1. Turn off printer
2. Hold down Resume button and press Power button.
3. Keep holding down Power button and let Resume button go.
4. Press Resume button 2 times then let BOTH buttons go.
5. Green lights will flash and then stop blinking.
6. When green lights are solid, press the Resume button 4 times.
7. Press the Power button and the printer should turn off, if not,
press the Power button once more.
8. Your printer should respond as normal.


I hope this helps.

Cindy Wells
(most inkjets waste ink counters are set to hit their fill point at the expected end-of-life of the printer. Additional failures may happen soon.)

May 21, 2010 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

After downloading the disc for my cannon mp500 I try to open the cd label print and a message comes up with "a compatible printer for printing cd media was not found"


please you are frist time instoll a printer driver cd ?
if yes then second time this driver cd is not excepted. beacose you this cd is out of your pc. and this message is not coming.

Oct 10, 2009 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

Cannon ip3000. light flashing green/orange and service error 6A00 coming up. What's wrong?


6A00 means the purge unit is stuck, it's the unit on the right that cleans the printhead. If you can see on the right, look for any paper scraps or things that don't belong. Otherwise it's a shop repair.

Aug 25, 2009 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

Will not print.. cannon pixma ip3000


Ink has dried in the printhead. You need a new one, QY6-0064-000, around $50.00

Jun 30, 2009 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

Cannon Pixma IP3000


Hi there,

Error 6A00 is a printer sheet feed unit error.
You need to send into repair in any canon autorized service center.

Just let me know if you need further assistant

pincer



Apr 07, 2009 | Canon PIXMA iP3000 InkJet Photo Printer

2 Answers

Service error 5200 on a cannon pixma ip3000


i have the same problem using nero cover designer
it's very slow quality is ok but at 1/4 of the page it gives me the error message....

PAT

Mar 22, 2009 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

Canon pixma ip3000 printer


Go here. In the search box in the center of the screen, type "BJ metafile error" and click the Search button. Select the first answer that comes up. Use the second solution to turn off background printing.

Jun 18, 2008 | Canon PIXMA iP3000 InkJet Photo Printer

1 Answer

Freezing up cd label print


Do you have the right firmware settings? http://www.crn.com/white-box/188100839;jsessionid=KRPY0I315LR2AQSNDLRSKHSCJUNN2JVN?pgno=1

Apr 11, 2007 | Canon PIXMA iP3000 InkJet Photo Printer

Not finding what you are looking for?
Canon PIXMA  MP810 All-In-One InkJet Printer Logo

818 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

old marine
old marine

Level 3 Expert

2260 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Canon Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...