Question about Dual XDVD8170 Car DVD Player

Open Question

Hi all i need the Wire diagram from a DUAL XDVD8170, please if someone can put some pictures from connector (10 pins)conector.

Posted by on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 19 Answers

SOURCE: missing parking brake wire dual xdvd 8180, where

TOP SIDE SAME SIDE AS LATCH, TOP LEFT

Posted on Jan 02, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Problem with panel front conector in Dell Dimension 2200 motherbo


The following information is to assist you in performing the right connections. You should take precautionary measures such as grounding yourself and completely disconnecting the PC form any source of power.

This picture shows the connector for the front panel power button, reset button, and power and hard disk lights: an 8x2 pin connector with 1 pin missing:



0505a76.jpg
The table below lists the pinouts for the connector. The orientation of this table is the same as the picture above, this shows the top part of the connector. All the pins below pin 8 appear to be non-connected.


f07048e.jpg


Each pair of pins labeled Power and Reset goes to the 2 wires for the corresponding button. The hard disk and power LED wires connect to the corresponding LEDs, you need to ensure the proper polarity of the + and - wires for each LED or it will not illuminate.

The above information is for your information only.

Mar 01, 2010 | Dell (2M502) Motherboard

1 Answer

Telex 56 to cobra 4 pin


Hi there!!

the yellw wire is not used on the microphone conector most of them are just cut and left in there loose as long as its not shorting out on anything!! The wiring for the telex 56 for your radio Cobra 29 LTD is as follows: PIN #1 Shield & Red, PIN #2 White, PIN #3 Blue, PIN #4 Black, Yellow wire not connected!!

If you notice when you have the connector apart on the back of the pins where the wires get soldered to the pins are numbered so you will know which pins they are or on the front side of the connector the pins are also marked wich numbers they are!! If you have any other questions please feel free to e-mail us at: bigdscbshop@hughes.net

Apr 18, 2009 | Telex M-560 Consumer Microphone

5 Answers

Cdv 710 silver crest dvd is not working


Silvercrest has a policy about traffic security! they deliver car audio and dvd players with no possibility to watch video while driving !I went to a car audio specialist and they connected a brown cable which was the handbrake cable to the ground (a black cable and then the pro was solved!I didnt see the warning (enjoy music only while driving) i could watch dvd while driving and my pro was solved ..

Mar 25, 2009 | Car Audio & Video

3 Answers

LG 17'' LCD Monitor VGA 15 pin connector pin diagram


pin no 1 - Red colour signal (Red colour wire)
pin no 2 - Green colour signal (Green colour wire)
pin no 3 - Blue colour signal (Blue colour wire)
4&5 Not connected
pin no 6&7&8 are (Grounds)RGB Returns
9&10 NC
pin 13 Hohizontal sync signal
pin no 14 vertical sync signal
Not nessasry other pins

Nov 17, 2008 | LG Studioworks 700S 17" CRT Monitor

1 Answer

Hoowww


You need to put it on a switch that goes to ground in one position and in the other position it needs nothing connected. Then you flip the switch to ground it when you what to watch the video

Jul 01, 2008 | Dual XDVD8170 Car DVD Player

1 Answer

Wiring harness on my 94 Ranger


I have a 94 Ranger XLT extended cab. Here are the power/ ground connector pinouts and wire colors as shown in the factory service manual:
Pin 1 LG/Y Radio Memory Power (B+)
Pin 2 BK Ground
Pin 3 Y/BK Power (Hot in RUN or ACCY)
Pin 4 LB/R Illumination (dims with dash lights)
Pin 5 O/BK Illumination (does not dim)
Pin 6 BK/LG Ground

From the diagrams, looks like either ground will work.

Hope this helps.

May 30, 2008 | Car Audio & Video

2 Answers

Need wiring diagram for emachines t2200 motherboard


If you are replacing the power supply and it has 4 pin 12v conector and your motherboard doesn't, just disregard the 4 pin plug. The 20 pin conector will supply sufficient power for the processor. Many of the older motherboards did not have a separate 12v supply for the processor.

Apr 18, 2008 | E-Machines eMachines Desktop PC

6 Answers

PS2 Controller Wiring Diagram


heres the diagram

http://www.curiousinventor.com/guides/ps2

Dec 09, 2007 | Sony PS2 Dual Shock 2 Controller...

1 Answer

Lose wire with 6Wires connector... need diagrams of pin out


(There are different versions of the ba-200, so I'm assuming they al use the same wiring/pinout...) if you look at the amp on the enclosure(right-side up... so the writin goes left->right): The top left pin is #1, beside it is #2, then #3. The bottom left pin is #4, beside it is #5, then #6. #1 Right speaker positive input #2 Empty #3 12 Volt Constant Power #4 Left speaker positive input #5 Remote turn on / Acc power input #6 Ground Now there's supposed to be a 15-amp fuse on pin #3 (12v constan power).

Aug 22, 2006 | Audiovox BA200 Car Subwoofer

Not finding what you are looking for?
Dual XDVD8170 Car DVD Player Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dual Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

5013 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8981 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Dual Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...