Question about GE Security Simon 3 Wireless Home Security System
I have GE Simon 3 Security System (60-875) installed at my house for more than 3 years. Now for the last whole week it start a cycle of 2 beeps after every couple of hours or so. When I press the "System Status" it goes away, and start again after couple of hours.
"System Status" says, "System Low Battery". My question is do I need a new "Lead Acid Battery" for it. This battery is supposed to be rechargable, and so I'm working why does it have to replaced.
If I do need to replace this "Sealed Lead-Acid" battery, can you tell where I can get it from internet.
Thanks so much
I install these panels. For the low battery message to clear you need to power the system down completely. To do this you need to unplug the battery and also unplug the transformer plugged into an electrical outlet. When you power the system back up, you need to first plug in the battery leads. Then the transformer.
Posted on Apr 21, 2009
Once you open the main panel and it asks you for your access code for programing, look back on the top where the clip for the main panel is, you'll see another clip in there, use a small screwdriver to push in and press and release, then you'll see a small compartment with 2 philip head screws...there's the battery.
Posted on Jul 09, 2008
When you replace the alarm panel battery with a new one, you must first disconnect or switch off the mains electricity to the unit, then replace the battery before finally reconnecting the unit to mains power. If you do not follow this sequence, the panel will continue to give a low battery warning even though you have replaced the battery with a new one.
Posted on Oct 10, 2010
This is for use when you have gotten a low panel battery and replaced it , but it still says system low battery. Power down the system by unplugging the a/c power and main panel battery. Wait 30 sec, then hook the battery up first followed by the a/c power transformer. You will have to set the time, but the low battery trouble will go away.
Posted on Aug 02, 2010
No, after changing the battery and powering down the system completely to clear the "system low battery" message, it still remembers all your programs. The only thing it loses is the time which can be set again easily.
Posted on Nov 19, 2009
Once the battery has been replaced, I am still getting the low battery message. Is there a reset code?
Posted on Aug 05, 2008
I just replaced my system battery and that stopped the beeping. I got the replacement battery from Batteries Plus. It costs 10 bucks. It was easy to replace the old battery, it took about 5 minutes.
Posted on May 14, 2010
I followed all the instructions exactly and the low battery beeping stopped for a little over 2 hours and then started up again. HELP it is driving me crazy
Posted on Sep 02, 2011
After changing the battery and powering down the system completely in order to clear the "low battery" message, will I need to completely reprogram the panel to the settings I want? Will everything go back to the factory defaults?
Posted on Aug 04, 2009
Hey - I may be an idiot, but how do I even remove the panel to replace the batteries on the main panel?
Posted on Aug 25, 2009
I have the same Security System the same problem, with the 2 beeps every couple of hours .
The Control Center called and said the battery on the door connector was low and that was the cause of the beeps not the entire system, I replaced with 2 triple A batteries and no more beeps.
Posted on Nov 08, 2008
Thank you guy's for all your help. Got the battery at Fry's. $16.30 out the door. Had to plug battery in first then it cleared the fault. Did not clear fault when power supply was plugged in first. Yup it's a simple thing. Just had to reset the time.
Posted on Apr 05, 2011
I don't use my system anymore how do I shut the every two hour beeping for good. is there another option other than jumping through all the battery hurdles if I don't wish to use it.
Posted on Jun 02, 2011
I had the same problem. An electrician came out and couldnt fix it.I am girl who know nothing about this but I get trying.I bought a new 6V1.2AH battey for the panel on line at batterybob.com I replaced it. (to get the cover open put a screw driver in the round and square slot and pull). stil kept bepping. unpluged the transformer-still bepps-went to the front door and back door replaced the AAA batteries. Open every window and door and closed back tightly. waited 10 minutes put the transformer in. Finally-It stopped!!! and my headache is gone!
Posted on Feb 05, 2011
The battery is a GE 60-914 which you can find on the internet. My problem is how to open the panel to get to the battery!
Posted on Jul 07, 2008
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Nov 16, 2010 | GE Security Simon 3 Wireless Home Security...
Jan 14, 2010 | GE Security Simon 3 Wireless Home Security...
Oct 07, 2009 | GE Security Simon 3 Wireless Home Security...
Sep 20, 2009 | GE Security Simon 3 Wireless Home Security...
Jul 04, 2009 | GE Security Simon 3 Wireless Home Security...
Jun 16, 2009 | GE Security Simon 3 Wireless Home Security...
Jun 12, 2009 | GE Security Simon 3 Wireless Home Security...
Apr 15, 2009 | GE Security Simon 3 Wireless Home Security...
Jan 25, 2009 | GE Security Simon 3 Wireless Home Security...
Oct 19, 2008 | GE Security Simon 3 Wireless Home Security...
31,684 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: