Question about Westinghouse Dishwashers

1 Answer

I a Westinghouse dishwasher 920 and a plastic spoon fell onto the element while it was on and its melted the spoon on the heat element and i cant remove it. how do i replace the element i am a motor mech so i am mech minded Kind Regards Chris

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 618 Answers

Break as much of the plastic off as you can and just let the rest melt off or melt it with a solder gun . won't hurt anything. If you want is easy to replace just hall machine from hole and tilt back remove the wires and the nuts holding it on .

Posted on Dec 03, 2010

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A spoon will a plastic handle melted on the circular heating element on the floor of the dishwasher. It is stuck on there, should we pry it off? Will the dishwasher still work? What do you suggest?


Hello, Thank You for using FixYa. I will be helping you today. Yes i would remove as much as you can you wont damage the heating element. Then run a cycle with heated dry and check after the cycle if you can remove the fest.
Thank You and please rate my answer if it was helpful..

Jun 22, 2011 | KitchenAid KUDK03ITBK Built-in Dishwasher

1 Answer

Melted a spoon on element. What can I do to remove plastic on element


The way to remove it is you need to raise the temprature of the element to the level when the spoon melted, not so easy of a task, but nothing else will do it.

I would fire the element, and be ready with a damp terry cloth towel, and wipe the spoon free. Another way would be to use a propane torch, but you MUST protect everything around the element or you will cause more damage.

The key is that you have to acheive the same temprature that melted the spoon, and it will release and leave little, if any residue..

Feb 22, 2011 | Kenmore Elite Stainless Steel 24" BuiltIn...

1 Answer

A piece of plastic spoon melted on heating element. Is there a way to clean it off.


Make sure the heating element is cool. Remove as much of the melted plastic off that you can by hand first. You can use a straight edge razor to lightly scrape it off. When you have most of the material removed, get some fine emery paper or steel wool to finish removing it. DO NOT use anything that is so abrasive that it penetrates the outer shell of the heating element. Once a hole forms and water gets inside, the element has to be replaced. I hope this helps you.

NOTE: I would not recommend using any kind of cleansers as they tend to leave residue.

Feb 08, 2010 | Dishwashers

1 Answer

Plastic spoon dropped onto the hearing element. does element need to be replaced?


no you dont need to do anything but remove the spoon from the heater. the heater wont be harmed and will continue to work properly.

Jan 03, 2010 | Maytag 24 in. MDB6100A Built-in Dishwasher

2 Answers

Plastic melted on Dishwasher heating element


youll have to run a whole cycle again and pay attention to when the heating element comes on again. Once its hot the plastic will be soft enough to remove it with a tight cotton rag. Use you oven mitts for protection. Hope this helps

Dec 01, 2008 | Frigidaire 24 in. FDB1050REC Stainless...

1 Answer

A child's plastic cup top melted on heating element. . .how to remove residue


Gently scrape with a razor blade or paint scraper to remove the large pieces, then use some emery paper or very fine sand paper to remove the rest. Use care when applying any pressure on the element, and try not to leave any gouges in the element surface. I have also had good luck with a nail file. Hope this helps you.

Feb 01, 2008 | GE 24 in. Profile PDW7800 Built-in...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

312 people viewed this question

Ask a Question

Usually answered in minutes!

Top Westinghouse Dishwashers Experts

GPEC

Level 1 Expert

12 Answers

The GreyOne
The GreyOne

Level 2 Expert

32 Answers

Kenneth Simmons

Level 3 Expert

1032 Answers

Are you a Westinghouse Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...