Question about KitchenAid Architect Series KEBC107KSS Electric Single Oven

1 Answer

I have a kitchen add KGSS907 it is showing an error message F6E0 lost communications how do I correct this

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 417 Answers

F6 E0 means the switch pulse return line to the electronic control is not connected

The usual way to correct this is to replace the electronic control (clock).

You might want to check for loose or burnt out wires on the clock unit before replacing tho'.

Posted on Dec 17, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mbleoven had a E2-F2 code what is the oro


The F2 class of error messages means that the keypad and the control unit aren't communicating properly. First turn off the circuit breaker to the range for a minute. Check if the error recurs after you clear the PF message. If the error recurs, turn off the power again. You need to check the wiring between the keypad and the control unit. Make sure that all of the wire harness connections are fully seated and all the wires are undamaged. It's not uncommon for one wire to get broken so check the continuity.

If that doesn't help, you probably need a new keypad. If you add a comment with the model number of your oven, I may be able to point you to a supplier.

I hope this helps.

Cindy Wells

Nov 22, 2014 | Whirlpool Ovens

2 Answers

Error code F6E0 on Kitchenaid KGSS907000 wondering if it is the control board or touch screen, what other components could cause this?


F6 - E0 Return line not connected If switch pulse return line is not connected, electronic control will display F6 within 60 seconds after power up. Replace control board

May 02, 2014 | KitchenAid Architect Series KEBC107KSS...

1 Answer

F6 E6 error code?


Hi,

This fault is a communication error at the appliance manager, could be a loose wire or a bad display transformer, either way you will need a certified technician to fix this issue, there is no simple plug and go issue to resolve. I personally found the problem to be the transformer not send voltage to the appliance manager. This is solvable but needs someone who understand electronics to correct this issue.

F6 E0 Oven user interface - lost communication E6 Oven appliance manager 1 (upper, single) - lost communication

This is directly from the tech sheet of your oven and directly from the factory web site.

Good Luck

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Dec 03, 2013 | KitchenAid KEBS179B 27" Built-in Electric...

2 Answers

Shortly after end of 1 year warranty, KEMS378SSS04 began displaying F6E0 Lost Communication on lower over UI (not on the microwave). Turning power off/on (multiple times required sometimes) fixes the...


Hi,

Below is the complete instruction sheet.

You are having a communication error between the appliance. Here is the actual tech manual instructions for that code:

PROCEDURE: Before proceeding, press OFF, OFF, START to enter Diagnostic

mode and verify the error codes. Ensure AM software, UI software and EEPROM

CHECKSUM versions appear on the lower text line. If AM software and EEPROM

versions do not appear, UI and AM may not be communicating. Verify this for the

lower oven UI and for the microwave (upper oven) UI. The lower oven UI will show

the AM software version for the lower oven appliance manager, and the microwave

UI will show the AM software and EEPROM versions for the microwave appliance

manager.

If the lower oven UI is not displaying the AM software version, go to UI IS NOT

DISPLAYING AM SOFTWARE VERSION.

If the upper oven UI is not displaying the AM software and EEPROM versions,

go to UPPER OVEN UI IS NOT DISPLAYING THE AM SOFTWARE AND

EEPROM VERSIONS.

If lower oven UI and microwave UI are both displaying an error, go to LOWER

OVEN UI AND MICROWAVE UI ARE BOTH DISPLAYING AN ERROR.

UI IS NOT DISPLAYING AM SOFTWARE VERSION:

A. Unplug oven or disconnect power.

B. Open the back panels and make sure the P6 and P2 connectors are fully

inserted on the appliance manager and on the lower oven user interface board.

- If they are not plugged in, plug in connectors and go to step F.

- If they are plugged in, go to step C.

C. Visually inspect all wires between P6 on the appliance manager and P2 on the

lower user interface.

- Make sure wires are not cut or pinched.

- If the wires appear to be intact, perform a continuity check between

P6-1 of the appliance manager and P2-1 of the user interface board.

Complete for P6-2(AM) to P2-2(UI), P6-4(AM) to P2-4(UI) and P6-5(AM) to

P2-5(UI). All the measurements made should be less than 5 ?. If any of

these measurements exceeds 5 ?, go to step E.

D. Replace the appliance manager. Ensure all connectors are properly inserted.

E. Replace the wiring harness (signal). Ensure all connectors are properly inserted.

F. Replace all parts and panels before operating.

G. Plug in oven or reconnect power.

H. Observe for longer than 1 minute to determine if error has been repaired.

I. If error does not appear, initiate a bake cycle. Let the cycle run for at least

1 minute.

- If no error occurs, cancel the cycle, the problem has been repaired.

- If error occurs again, restart the troubleshooting procedure at step A.

At step D, replace the lower oven user interface board if appliance

manager has already been replaced.
- If both are replaced the problem has been repaired.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

May 22, 2011 | Ovens

1 Answer

Oven does not work is reads F6E0 error code lost communition what's wrong?


I assume it's a KitchenAid that you have. Here you can find a previous thread about this code:
https://www.fixya.com/support/t1176150-f6e0

Oven repair in Santa Ana, CA
Appliance repair in Santa Ana, CA

Jan 24, 2011 | Ovens

1 Answer

Kitchen aid ykesa907psoo has error message showing "wd sensor open" can you tell me what this is and how to address it thanks


Can't find that error but probably is reffering to the Warmer Drawer sensor . Try replacing or check for broken wire.

Nov 20, 2010 | Ovens

1 Answer

We installed kitchen aid microwave convection oven model kems308. it is displaying error code F6E0, "Lost communication". Any idea on how to fix?


Turn the power to the oven off. It usually is not possible to unplug the power chord for the built-in appliances so go to the main switch board and just turn off the oven power for about 5 minutes and then turn on the switch. The error code should disappear. Mine did!
Chander Mehta

Jun 06, 2010 | KitchenAid 27 in. Built-in...

1 Answer

Error on display F1 & E1 Stove will not start


HI. This is a safety flip flop error code, caused by damaged circuitry within the electronic control board. This will require you to have the control replaced asap. This will correct the issue.

Part number (for white control) #3196971
Part Number (for black control) #3196970

Oct 19, 2009 | Ovens

13 Answers

F6E0


Last night I saw the lights in the house flicker momentarily... This morning, I turned the oven on, set it to Bake and within a few seconds, the control panel reported error code “F6 E0” then shut the oven off. The control panel also reported "Lost communication...". I read on another site that this code may require replacing the control panel itself. Apparently, the momentary power fluctuation wasn't large enough to damage the electronics (since the control panel still works), but was significant enough to confuse the electronics controlling the oven. To fix the oven, I simply turned the 30 AMP breaker for the oven off for about 5 minutes. When I turned it back on, the oven worked just fine. Solution #1 recommends taking off the control panel, which voids the warranty. It's more likely that it was fixed just by cycling power to the oven via the breaker.

Oct 27, 2008 | KitchenAid Architect Series KEBC107KSS...

3 Answers

Kitchen Aid ovens - error codes


The F-3 error code typically means you have sensor problem. The sensor is usually mounted in the oven space up near the top of the unit. The first thing to do is turn off the circuit breaker to the oven. Do you have an ohm meter? I suggest if you don't to purchase one. They are relatively inexpensive. Maybe you can borrow one from a friend. Disconnect the sensor from the electronic control and measure the resistance. There should be a wiring diagram in the top of the unit that will help you to locate the sensor wires. Most sensors should read around 1100 ohms at room temperature. If sensor reads as an open circuit or has a very high resistance, it must be replaced. If instead it reads very low, then there is a short in the wiring. Some units have a fuse in series with the sensor. Check to see that the fuse has not blown.

May 02, 2007 | KitchenAid KEMC378 Electric Double Oven

Not finding what you are looking for?
KitchenAid Architect Series KEBC107KSS Electric Single Oven Logo

680 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Ovens Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

jdthefixer

Level 3 Expert

746 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a KitchenAid Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...