Question about Hobart A200 Stand Mixer

1 Answer

A200 spec 3943 bearing bracket broken where to get one? the one that supports the rotor on the back of the machine...

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Hobart Expert
  • 119 Answers

Check www.hobartservice.com for your local Hobart office.

Posted on Sep 13, 2011

  • Chris LaSalvia
    Chris LaSalvia Jun 28, 2014

    Were you able to find the bearing bracket? I'm also looking for one and Hobart does not carry that anymore.

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change hobart a200 motor bearings


Do not heat up you have to strip the gear box but not all take the top gears off but look what you are doing its got to go back the same way or it won't work you have to take the worm gear off and then you can take it out from the back but if you can't do it get in touch with **** at x bakery in Haywood and ill sort it for you hope this helps it is a big job sorry

Jan 06, 2013 | Hobart A200 Stand Mixer

1 Answer

Hobart A200 Noise


After viewing and listening to your video, my first guess would be bad bearing(s). The sound varies with the speed of the agitator, so the noise is at the speed of the transmission shaft or planetary area. These mixers use very common standard bearings. As such, they are available very reasonably from sources OTHER than Hobart. You will need to take the transmission apart in order to find and solve the problem. Study the parts manual in detail. It seems complicated, but once you understand it, it is logical. I highly recommend that you get a really good understanding of how it works and goes together before you start taking it apart though.

Nov 02, 2012 | Hobart A200 Stand Mixer

1 Answer

Hobart A200 mixer won't start


My fantastic guy just rebuilt my A200. He says it's likely that your back plate is slightly off center so that the center arbor is touching the windings-- any contact and the machine won't run. The tolerances are thousandths of an inch in there.

Nov 21, 2011 | Hobart A200 Stand Mixer

1 Answer

I've broken the agitator shaft pin on my Hobart A200T. I can find replacement pins online, but the local Hobart tech. is MIA. How do you remove the pin? How do you secure the replacement in the...


Drive it out with a punch and hammer. It's best to take the planetary off the machine so you can support the shaft. If not it puts a lot of unnecessary stress on the bearings and other parts.

Jul 08, 2011 | Hobart A200 Stand Mixer

1 Answer

Hobart A-200 3943. Having a problem with torque.


Check your recipe against the capacity chart found here: http://www.primasupply.com/images/hobarta200.pdf

You may be overloading the unit. Hope this helps.

Oct 13, 2009 | Hobart A200 Stand Mixer

2 Answers

Age of my a-200 mixer


if it has a spec.# instead of a ml.#it would have to be at least 25-30 yrs. old

Jul 04, 2009 | Hobart A200 Stand Mixer

2 Answers

A-200 mixer brush carrier orientation.


Hi. I can't help you with your first question...But I can help with your brushes problem. Unplug the mixer With the two inspection plates removed at the commutator end loosen the two screws of the brush holder which are above and below the motor bearing cover, they're the only larger screws now visible. Note the markings on the brush holder on the bottom right side where you removed the inspection plate. Rotate the brush holder to the other mark. Set the brush holder screws. Plug in the power. and start the motor. It should now be turning in the proper direction, if not, make small adjustments by loosening the set screws, and moving the brushes until it starts to your satisfaction. Be sure that the set screws are tightened when you're done. If you need further assistance, post a clarification.

I have the same spec. mixer as you do.

If this solution has assisted you, please rate it. Good luck! ricardok45

Mar 30, 2009 | Hobart A200 Stand Mixer

2 Answers

My 20 qt. mixer has no power in speed #1.


Hi All. Since the original poster has not responded to my request for ML and spec. #'s, I'll offer a solution based on a spec.# 3943 for anyone with the same problem. This is an older model A200 with a solid aluminum gearshift lever.

Stop using the mixer!!!

The slow speed gear (1st. gear) is engaged by a "diving key". Over time this key can wear to the point of failure, or break entirely and will no longer engage. This failure only affects the first gear, allowing the second and third gears to function properly. If you can stop the mixer attachment by hand while in 1st. gear, then you have the above problem. The unit must be serviced. If the key has been sheared there is the potential for a broken piece of this key to get into the trans. grease and cause further damage to the mixer. For a Hobart Tech., this is relatively easy to repair as a minimum number of parts need to be removed in order to expose the diving key.

Call your local Hobart office to schedule a repair. If you've never done any repairs on this model, do not tackle this project by yourself. I you have some experience with this model goto the hobartservice.com website, register for free and then download the parts list. Ensure that you have the list for the 3493 spec.

Good luck!

If anyone has been assisted by this solution, please rate it. ricardok45

Mar 17, 2009 | Hobart A200 Stand Mixer

Not finding what you are looking for?
Hobart A200 Stand Mixer Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Ross Keen

Level 3 Expert

1363 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Bruce Showalter

Level 2 Expert

133 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...