Question about Maytag Neptune FAV6800AW Top Load Washer

1 Answer

We have a maytag neptune TL. Usually when you hit start to run a load a little water comes out of the discharge hose. It is not doing that. It runs in the wash cycle for about 8 minutes the it pauses then makes a buzzing noise. No water ever comes out of the discharge hose. I am thinking that it the pump but not sure. Is there some way to test the pump? I would like to do the work myself to save the money. Any advice would be greatly appreciated. Thanks in advance for your help. God bless & Have a great day.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 335 Answers

If the machine is a FAV6800A or FAV9800A google ""Sticky: Neptune TL Washer FAV6800AWW""" Post your problem at this Forum. You will find the FAVA9800A/FAV6800A Service Manual at that site.

If the machine is a FAV6800A or FAV9800A you can go into Service Mode and tes the Drain Pump. Then we can start to troubleshoot the issue if the above model is your machine type.

This site is not really geared up for DIY folks.

Posted on Jan 10, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My maytag neptune tl stops after wash cycle it will start for a few secounds then stops and will continue this start stop action till i hit the stop button


The washer is trying to go into spin but failing. The two sprag clutches are probably sticking, This usually indicates a water leak.
The seal should be replaced. The bearing and sprag clutches should also be checked and will probably need to be relubricate or replaced.

Apr 15, 2016 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag Neptune TL washer overfilling


yes i would agree the water valve is defective as if unplugged it should close,but also sounds like a pressure sensor or pressure hose problem that is also defective too due to the fact that it should at least start the wash cycle even though the water doesn't stop filling,so also it could be the central control unit,pressure switch or pressure hose

May 07, 2012 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag Neptune TL washer doesn't stop adding water


it sounds like your drain hose is to low it needs to be 3 feet high if its to low this will cause the water to syphon out and keep refilling

Nov 22, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Why is there water in the floor model i just bought?


check your discharge hose in the back make sure it has not fell out of the drain a little. there is alot of preassure coming out of the hose. i'd say this is it . good luck

Feb 24, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

How to repair water over load on a maytag neptun fav6800w


I don't like using this forum but I will get you started.

You can't get the FAV6800A/FAV9800A Service Manual from this site.


Google this without the quotes""Sticky: Neptune TL Washer FAV6800AWW""" Post your problem at this Forum. You will find the FAVA9800A/FAV6800A Service Manual at that site.

Will the water turn off if you hit the OFF buton on the console or pull the 120VAC power cord to the washer?

Issue could be a Stuck open Water Inlet Valve or improper signaling from the Pressure Switch for water fill in the wash tub.........**** dh1200s

Jan 09, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

How do I drain the water out of a maytag neptune tl


Drop the outlet hose down from the back of the machine into a bucket

Remove all of the clips holding it onto the machine to get it as low as possible

Apr 01, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Start the wash . Lets say quick wash . error nd


HiYa ngateley



"nd" refers to a No Drain issue . check for restriction in pump assy, restricted drain hose loose wire at pump, bad pump.

please leave a solved rating before you sign off.

Mar 24, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Maytag Neptune TL.


easy!the water pressure switch is not working the little hose going to it could blocked or off,or the pressure switch bottle could be blocked. rate me if right Eire

Dec 02, 2007 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Maytag Neptune TL Washer


if this worked fine before, then I am only guessing that the water inlet valve has malfunctioned. try filling the machine with a garden hose...any change? if still no go, then be sure to have a shop-vac handy to remove the water you just added.

May 30, 2007 | Maytag Neptune FAV6800AW Top Load Washer

3 Answers

Neptune TL will not spin


Menco, check undernieth the consol, they usually have the tech sheet with test proceedures located there. Catriver..post back.

Aug 13, 2006 | Maytag Neptune FAV6800AW Top Load Washer

Not finding what you are looking for?
Maytag Neptune FAV6800AW Top Load Washer Logo

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

jimorris77

Level 3 Expert

411 Answers

Sheldon Dedek

Level 3 Expert

909 Answers

Bill Long

Level 3 Expert

606 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...