Question about Staples Office Equipment & Supplies

3 Answers

Spl-txc22a won't start, it is only a month old.The switch is on and have moved it to another plug in. Cleaned out the hopper and wiped off the sensor but nothing. No lights or power. I have unplugged it for the 80 minutes and am waiting.Thanks Ted

Posted by Anonymous on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a Staples Shredder SPL-TCX22A every time I put a piece of paper in the machine the Anti Jam light comes on and the machine will not work.

Posted on Mar 10, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Had the same problem. Here is what I found worked:
1. Shut off the power switch in the back.
2. Hold your finger down on the FWD button and at the same time, turn the Power button (in the back) on again. Keep your finger pressing the FWD button until the machine starts running.
3. Once the machine starts running it will stay running constantly for you to shred. It won't stop until you switch off the power button in the back. But at least the machine will run for big jobs. You'll have to keep an eye on the bin because apparently all sensors get switched off in this mode. However, it's better than junking a shredder that will otherwise work. Good luck!
Oh, and you have to do this every time to use the machine; the rests don't save. But again, I found this to be fine.

Posted on Feb 18, 2013

  • Dane Raven
    Dane Raven Feb 18, 2013

    Thanks! That works, and for the limited time I will be shredding, the unit won't overheat. Great answer!

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem with mine so I took the unit apart and checked the fuse and it was not blown, the motor turned fine, there were no jams. I found that after you turn on the power switch in the back, press REALLY hard on the main power switch on top and it turned right on. I know! how stupid did I feel! Hope this is a solution for your problem too :-)

Posted on Feb 23, 2014

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Staples SPL-TXC15A shredder that doesn't start when paper is inserted. The power light is on and it runs in reverse but won't start when paper is inserted.


You need to change the direction or travel switch. Auto will only work when the direction of travel is into the bin, but you probably know that. There is an interlock on it. Use a vacuum cleaner crevice tool and then the brush attachment on both sides of the head. If that doesn't work, my guess is that the forward reverse switch is faulty. You would need to strip it apart and check with a meter.

Jan 03, 2017 | Kitchen Appliances - Others

1 Answer

Starts runs great turn off the it won't start again


Generator runs then shuts off - YouTube

? 8:17
https://www.youtube.com/watch?v=6esHkPyygWw
Sep 6, 2011 - Uploaded by mainblind
How to make Generac generator run bypassing the low oil sensor and ... Great video on low pressure warning switch removal and ...Pulled off the shroud over the sensor. ... It wouldn't start so I replaced the spark plug, gas, and oil - then it did as yours. ... 1200 Watt Generator Won't start - Duration: 14:49.

gasoline engine on portable generator won't start what do I ...

answers.angieslist.com/gasoline-engine-portable-generator-won-start-I-d...
Apr 16, 2014 - gasoline engine on portable generator won't start what do I need to do ... PULL, Take OUT the spark Plug , make certain it is clean and DRY and then start allover again. ... start then when talking pulling rope use electric starter - if won't ...several times till starts, moving choke to OFF or RUN position once it ...

How To Fix A Portable Generator That Won't Start ' My ...

blog.mygenerator.com.au/how-to-fix-a-portable-generator/


Jan 21, 2016 | Electrical Supplies

1 Answer

My hopper wont dispesence on my bunn IMIX-5 Tim Hortons


take the hopper out and press the button. if the spindle in the back doesn't move, the gear motor is siezed and needs to be removed, cleaned, lubed, and rebuilt. if the spindle moves, empty the hopper and reposition the auger so that it sits in the connector in the back, refill and test

Aug 07, 2014 | Bunn iMIX-5S BLK Powdered Beverage...

1 Answer

Staples Shredder SPL-TXC22A always has the jam light lit and will not work even though there is nothing jammed. It works if I press and hold the down button twice. It also works continuously if I turn off...


Home office shredders get jammed because the mechanism is not self cleaning. If you remove power and expose the mechanism you may find that, indeed, a shard of paper is triggering the jam sensor. These shredders require periodic removal of the bits of paper from the mechanism, an exercise that can consume hours of picking with tweezers while thinking there must be a better way.

Dec 10, 2013 | Office Equipment & Supplies

1 Answer

Problem E 20


First - check the connector to the toner hopper. It isn't uncommon for a technician to leave this disconnected when servicing the copier.
Confirm that the toner and hopper sensors are being wiped completely. Check the Gear Train on the hopper assy it may be locked up.
or A possible bad hopper unit cable.

Jul 28, 2012 | Canon NP 6050 Copier

1 Answer

Won't start. Drained old fuel and added fresh; cleaned in-tank fuel filter; cleaned plug. Still won't start


i would take the plug out and and the spark plug wire on the plug and try cranking it over and make the plug is firing if there is no fire then the ignition coil is dead but if you have fire then its a carb problem rarely ever a timing considering most mowers are timed with key ways which prevent them from jumping time.but if you have fire your good their but my overall suggestion is to rebuild the carb and swap out the spark plug if the mower has set for a period of 6 months or longer.

Aug 26, 2011 | Garden

3 Answers

The touch pad of HTC Touch responds intermittently.


hi, its a error in the phone, I had this happen to mine. You will most likely have to sent it away for repair. Just reflash the stock ROM and make sure that you have reflashed the stock SPL if you where using hard SPL and you will be ok this site will help you flash: http://lievenvw.wordpress.com/2008/09/18/howto-flash-your-htc-diamond-or-htc-touch-pro-with-a-custom-rom/ thank you
vijay
(vote for me)

Sep 23, 2009 | HTC Touch P3450 Smartphone

2 Answers

Code E020 on a NP 4050


How about this, Take the developing unit out and take the ATDC sensor out and plug the hole up in the developing unit. Reinstall the developing unit and cheat the front door switch and plug the sensor back in and hold it in your hand and make a copy. Dose it vibrate? If it dose not the sensor is bad... If you really get tired of working on the problem and you don't go to the copier to often and they are not billable, try this.... Take the top cover of the dev. unit and spoon toner into the dev. unit till it is almost full and reinstall it and clear the error code in service mode and just remember to add toner in to it every so often.

Jul 13, 2008 | Canon NP 6050 Copier

2 Answers

Canon photocopier


Title : E020 Error Code Problem :
When you have followed all the steps from the troubleshooting guide in the Service Manual and still have not resolved the issue, here are some possible areas that might be related.


Solution :
1) Confirm that the toner and hopper sensors are being wiped completely.
2) Check the Gear Train on the hopper assy it may be locked up.
3) A possible bad hopper unit cable. FG5-5016-000. See The Parts Catalog page 620-2 item # 60.
Canon USA, Inc. Systems & Technical Support Division 1-800-528-2830

Jun 27, 2008 | Canon NP 6050 Copier

1 Answer

Won't come on?


I just bought a brand new unit and as recommended I unscrewed the top bean hopper and the coffee ground container-cleaned and wiped.After that I screwed back everything and tried to grind some beans.The timer was ticking away but the grinder just refused to start.I switched off the main and unscrewed the hopper and carefully screwed it back.Halfway through,I noticed and felt that you must balanced and screwed it with a smooth movement until the the whole piece is in place.The grinder just started without a hitch.This grinder has a protection circuit whereby if any part is not properly installed it will not start.

Mar 07, 2008 | DeLonghi Retro DCG59 Electric Burr Grinder

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

5,272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Staples Office Equipment & Supplies Experts

Mitch Vass
Mitch Vass

Level 2 Expert

147 Answers

Jim Keysor

Level 2 Expert

331 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

Are you a Staples Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...