Question about NEC VT595 LCD Projector

1 Answer

Thank you kindly in advance for any suggestions on the following issue with the NEC VT595. It will stay on for about 20 minutes and then cut out/off. Then I get the six interval flashing Power and Status lights (orange and yellow). Any solutions? Thanks, again!

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 55 Answers

Hi,
There is a good chance that the problem may due to overheating. The status light would be blinking when it turns off.
Remember to disconnect the mains supply before working on the projector..
You should ensure that there is adequate ventilation and air flow around the projector, and that it is not in a very hot or humid room. Clean the air filters, using a vacuum cleaner. You should not need to remove the filter to clean it. Do not wash the internal sponge filter. It's better to replace it with a new one. The air filters are located on the side of the projector nearest the lens, one at the front and one at the rear.

Posted on Feb 19, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

VT595 LCD Won't come on. Power light orange Status red Blincks Once every sec or so.


If the lamp life has exceded its safe working limit, it will probably go into a permanent standby mode, I used to have an NEC MT830, I had to hold down the off button for 20 seconds to reset the lamp life, maybe it will be something similar. If you have your manual, it may give instructions, if not there will be a downloadable manual on the NEC website.

Good luck

Aug 09, 2011 | NEC VT595 LCD Projector

1 Answer

Having a problem getting past the red blinking status and orange blinking when trying to start up a NEC VT595 projector. This is after installing a new bulb.


I have had the same problem with my NEC VT695, however, while trying to repair it, I actually broke off two pieces, first the arm that is attached to the lamp cover that depresses the button, and then the actual button itself. Does anyone know any way to bypass this need to have the lamp cover seated 'properly'?

Jul 13, 2011 | NEC VT595 LCD Projector

1 Answer

How do you change the bulb for the NEC model VT595? I have two men looking at it and can't work out how to remove the old one.


Slide panel out half an inch. Using thumb and index finger squeeze end of cover and pull out

Jan 24, 2011 | NEC VT595 LCD Projector

1 Answer

The image on screen is almost a dirty yellow colour and not sharp at all. Also where do I purchase new filters from?


Hi,
A yellowing image, especially if it's circular in shape indicates the BLUE LCD polarizer is burned from overheating or just a lot of hours on it & it needs to be replaced to make the yellow go away. You can purchase a new filter from hundreds of online retailers. Just do a search on Google for "NEC VT595 Filter"
REPAIRS:
If you're interested I do replace the polarizer filter panels. I have parts in stock for the NEC VT595. The repair quote is $50 & if you have it repaired the $50 is put toward the repair. The repair will include cleaning all the LCD panels, filters, lenses, etc. on the inside which will bring back the original sharp picture again. If you like you can email me at prmhelp@earthlink.net for more information on having it repaired.
Thank You,
Jim Peters
Big Screen Projectors
PRMHELP@EARTHLINK.NET

QUALITY NEW, USED & REFURBISHED PROJECTOR SALES & REPAIR
See our products on Ebay at Seller ID BIG*SCREEN*PROJECTORS
With over 3,000 sales we still carry a 100% positive feedback rating!


QUALITY NEW, USED & NEW PROJECTOR SALES & REPAIR
See our products on Ebay at Seller ID BIG*SCREEN*PROJECTORS
With over 3,000 sales we still carry a 100% positive feedback rating!

Nov 01, 2010 | NEC VT595 LCD Projector

1 Answer

How do i reset bulb hours on a NEC vt595


Here is the user manual for this projector, It should help with all your questions.

http://www.projectorcentral.com/pdf/projector_manual_3467.pdf

Apr 21, 2010 | NEC VT595 LCD Projector

2 Answers

Lamp light stays solid red . i already replaced bulb. any solutions?


Check your owners manual for diagnostics. You can find all documentation for your VT595/695 projector on the NEC support site.

The users guide indicates that the lamp timer needs to be reset. Instructions can be found on page 49 of the users guide.

Press and hold the HELP button on the remote control for 10 seconds to reset the timer.

Feb 05, 2010 | NEC VT595 LCD Projector

1 Answer

My nec vt595 wont start up the status light is flashing orange


The only time the "status" light will be orange is when you accidently press the cabinet button and the cabinet is locked.

However, if the "power" light is blinking orange it means that the projector is cooling down and you need to wait a few minutes.

Jan 03, 2010 | NEC Computers & Internet

2 Answers

NEC VT 595 wont turn on. Just red blinking light


I had this same problem with 2 NEC VT595 projectors. My problem was that there was a broken "tab" on the lamp cover (the plastic cover that slides in place over the lamp) that is supposed to depress a switch which insures the lamp cover is in place before operating the projector. The tab was broken in half and not making the connection there for causing the blinking status light (.5 sec on, 2.5 sec off) indicating a lamp housing or cover error.

May 28, 2009 | NEC VT595 LCD Projector

1 Answer

Nec VT595 shows only wallpaper


It could be the laptop settings. You have to clone the output of you video card. You might have extended desktop setting selected. See if your mouse shows up when you scroll it across the screen. (go all the way left or right) . If you have questions you can call me 1-646-441-5254 Hope this helps.

Apr 14, 2009 | NEC VT595 LCD Projector

Not finding what you are looking for?
NEC VT595 LCD Projector Logo

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top NEC Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2239 Answers

The Knight
The Knight

Level 3 Expert

76204 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a NEC Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...