Question about Cisco 7910 IP Phone

1 Answer

How to unlock cisco ip phone 7910 - Cisco 7910 IP Phone

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 125 Answers

  1. Press **# in order to unlock Network Configuration on the phone.
  2. Press Settings.
  3. Press 3 on the keypad (or scroll down) for Network Configuration.
  4. Press 33 on the keypad (or scroll down) for Erase Configuration.
  5. Press the Yes softkey.
  6. Press the Save softkey.

Posted on Mar 03, 2011

Ad

3 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

spydersig

  • 17 Answers

SOURCE: How can I clear /

How to set a Cisco IP phone to factory default Reset configuration of Cisco IP Phone (7910, 1911, 7940, 7941, 7960, 7961)

To set the Cisco IP phone to factory default completes the following steps: should be completed:

For 7940, 7941, 7960, 7961 phones:

1. Power up the phone (unplug power cable and plug in again and hold the # key.
2. Release # when lights start flashing.
3. Press 123456789*0#.
4. Press 1 to keep network configuration or 2 to lose the network configuration.

For 7906G and 7911G phones:
1. Power up the phone (unplug power cable and plug in again and hold the # key.
2. Release # when MWI starts flashing.
3. Press 3491672850*#.

Posted on Jan 11, 2011

Anonymous

  • 1 Answer

SOURCE: 7910 IP Phone

you stupid ****! it needs a voice vlan

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My cisco ip phone 7960 is stuck in boot up mode after performing the soft reboot. i press 123456789*0#


You can try a couple of things: Unplug the power cable from the phone, hold dows the # key, and then plug the power cable in again. The phone begins its power up cycle. Release the # key after the Speaker button is no longer lit. You should see the following message on the phone: "Reset key sequence detected" Press 123456789*0# within 60 seconds after the Headset, Mute, and Speaker buttons begin to flash. If you enter this key sequence correctly, the phone displays this prompt: Keep network cfg? 1 = yes 2 = no In order to maintain the current network configuration settings for the phone when the phone resets, press 1. In order to reset the network configuration settings when the phone resets, press 2.
Or to perform a full reset: Press **#** to reset the Cisco IP Phone 7960

Mar 15, 2011 | Cisco 7910 IP Phone

1 Answer

How can I clear / reset a Cisco IP Phone 7910


How to set a Cisco IP phone to factory default Reset configuration of Cisco IP Phone (7910, 1911, 7940, 7941, 7960, 7961)

To set the Cisco IP phone to factory default completes the following steps: should be completed:

For 7940, 7941, 7960, 7961 phones:

1. Power up the phone (unplug power cable and plug in again and hold the # key.
2. Release # when lights start flashing.
3. Press 123456789*0#.
4. Press 1 to keep network configuration or 2 to lose the network configuration.

For 7906G and 7911G phones:
1. Power up the phone (unplug power cable and plug in again and hold the # key.
2. Release # when MWI starts flashing.
3. Press 3491672850*#.

Oct 28, 2010 | Cisco 7910 IP Phone

1 Answer

I am trying to unlock my phone to program it under sip


Hello,
Complete these steps:
1.On the Cisco IP Phone, press the Settings button.
2.Press **#
3.When the window displays Settings Unlocked, click the More softkey.
4.You now see the Erase softkey, which can be used in order to erase the configuration on the Cisco IP Phone.
I hope that this has been very helpful for you

If this solution will not helpfull for you that time pls send me a IP Phone details.

Jan 01, 2010 | Cisco 7940 IP Phone

1 Answer

How to Install LIP 7016D - IP Phone,I dont know which IP addresses should I give.


Hello,

For startimg IP Phone you should have a Router details e.g. TFTP, Gateway (Router IP), if DHCP is configured on your router that time that time pls don't assign mannualy IP on IP phone.

Hello,
Complete these steps:
1.On the Cisco IP Phone, press the Settings button.
2.Press **#
3.When the window displays Settings Unlocked, click the More softkey.
4.You now see the Erase softkey, which can be used in order to erase the configuration on the Cisco IP Phone.
I hope that this has been very helpful for you

Dec 23, 2009 | Computers & Internet

1 Answer

How can I unlock a SPA922 that has ben Locked? I can´t do factory resett becouse it is locked!


Hello,
Complete these steps:
1.On the Cisco IP Phone, press the Settings button.
2.Press **#
3.When the window displays Settings Unlocked, click the More softkey.
4.You now see the Erase softkey, which can be used in order to erase the configuration on the Cisco IP Phone.
I hope that this has been very helpful for you

Dec 18, 2009 | Linksys SPA922-EU IP Phone

1 Answer

Converting Cisco 7940 IP Phone to SIP


Unlocking a Cisco 7940

Method 1:
1) Unplug the phone
2) Plug the phone back in while holding the # key
The phone will soon display “Reset key sequence detected”
3) After several lights flash press the following keys in order:
1 2 3 4 5 6 7 8 9 * 0 #
4) The phone will then ask you if you want to save the network configurations:
Save network cfg? 1=yes 2=no
5) The phone will soon display “Factory reset initiated” and will continue
through the boot up process.
If that process fails to work for some reason there
is a second method.

Method 2

Complete these steps:
  1. Press Settings.
  2. The Network Configuration lock symbol must be unlocked. If not, exit to the main window and press ** # again.
  3. Press 3 on the keypad (or scroll down) for Network Configuration.
  4. Press 33 on the keypad (or scroll down) to Erase Configuration.
  5. Press the Yes softkey.
  6. Press the Save softkey.
The phone will now be reset.

Also see this link
http://www.cisco.com/univercd/cc/td/...tain.htm#93250

May 18, 2008 | Cisco 7910 IP Phone

2 Answers

7910 IP Phone


please check if firewall is ON on your netgear router...

Dec 12, 2007 | Cisco 7910 IP Phone

1 Answer

Cisco ip phoe


Is the phones registered to CallManager or CME?
if CM, then it could be because of partitions and Calling Search Spaces. PTs are placed on the line and are restricted by CSSes. http://cisco.com/en/US/docs/voice_ip_comm/cucm/admin/4_1_3/ccmsys/a03ptcss.html#wp1020642

If it is CME, then it could be a configuration issue
http://cisco.com/en/US/docs/voice_ip_comm/cucme/roadmap/itsph.htm

Nov 10, 2007 | Cisco 7910 IP Phone

1 Answer

Cisco 7960G IP Phone Problem


Try to manually reset the phone - **#"Settings" (this will unlock the configuration) + Network + menu under number "33" - erase the configuration. Then the phone configuration will be erased. Also you can manually set IP address and TFTP server

Sep 11, 2007 | Cisco 7940G IP Phone

Not finding what you are looking for?
Cisco 7910 IP Phone Logo

Related Topics:

1,364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Jeffrey Groves
Jeffrey Groves

Level 3 Expert

573 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...