Question about HP ProCurve Switch 2510G-24 24-Port Gigabit (J9279A#ABA)

1 Answer

I want reset the factory default of my switch HP Procurve 2510G

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

To reset using the CLI, run the command "erase startup-config". When prompted, say yes to reboot and that will restore the procurve switch back to factory settings after it starts up.

Posted on Mar 08, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I scan a photo from my HP2512 all-in-one


Depending on your operating system, see the following website:
http://h10025.www1.hp.com/ewfrf/wc/documentSubCategory?tmp_rule=30484&tmp_task=useCategory&cc=us&dlc=en&lc=en&product=5231933

Oct 09, 2014 | HP ProCurve Switch 2510G-24 24-Port...

1 Answer

What is the default IP of HP ProCurve 2510-48 ?


There is no IP address when the switch ships from the factory. It is set by the user and/or the network by DHCP. If you do not know what the IP address was set to, then you'll need to return the switch ti it's factory default configuration. There should be information in the manual for the switch about the default config.

Jul 02, 2014 | HP ProCurve Computers & Internet

1 Answer

How to factory default Procurve 224M J3299A using console and/or Reset/Clear


There's a reset button on back. When pressed in a specific pattern the switch is returned to the factory default configuration. Chapter 8 discussed this in the following manual:
ftp://ftp.hp.com/pub/networking/software/59672145.pdf

May 07, 2014 | HP ProCurve 224M (J3299A) Networking...

1 Answer

Hp procurve 2510g-48 switch keeps freezing up after power outage


Sounds like the power outage was caused by a power surge. That could have damaged the switch, hence the reason for the freezing. I would look to getting it replaced.

Apr 30, 2014 | HP Computers & Internet

1 Answer

Default password j4868a


The switch ships from the factory with no default username and password. If someone set it and you do not know it then you'll have to reset the switch to it's factory default configuration. There is a reset switch on the back of the unit and when pressed/held in a certain sequence the switch will reset. You'll need to look up the proper procedure in the user's guide of the switch.

Mar 07, 2014 | HP ProCurve 2124 (J4868A#ABA) 24x10/100...

1 Answer

Forgot password


You may have to reset the switch to the factory default configuration. There is a procedure for this in the manual for the switch.

Feb 13, 2014 | HP ProCurve Switch 1800-24G, 22-Port Web...

1 Answer

Default password for HP procurve j4899a


This link should tell you the answer. http://h30499.www3.hp.com/t5/Switches-Hubs-Modems-Legacy-ITRC/Clear-password-in-Procurve-2650/td-p/4598369#.U0sRNfldUok

Nov 01, 2012 | HP Hewlett Packard J4899B New ProCurve...

1 Answer

J9400b defult ip adress


There should be no default IP address on a 2626 switch. HP Procurve switches are setup by default to get an IP address by DHCP. To execute the factory default reset on the switch, perform these steps:
  1. Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
  2. Continue to press the Clear button while releasing the Reset button.
  3. When the Self Test LED begins to blink, release the Clear button. The switch will then complete its self test and begin operating with its configuration restored to the factory default settings.
Be aware, using these instructions will wipe out any configuration you have on the switch

Good Luck

Jan 21, 2012 | HP ProCurve 2626 (J4900B) 24x10/100 Mbps...

1 Answer

Lost enable password for 2510G


attempt to log into the system. While it's asking for the password, press the clear button on the front of the system. This will let you into the switch programming.

Dec 30, 2010 | HP ProCurve Switch 2510G-24 24-Port...

Not finding what you are looking for?
HP ProCurve Switch 2510G-24 24-Port Gigabit (J9279A#ABA) Logo

8,212 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Computers & Internet Experts

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Toby Lee
Toby Lee

Level 3 Expert

409 Answers

Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...