Question about Kenmore 73502 / 73504 / 73509 Bottom Freezer Refrigerator

Open Question

Trio 795.75546400 follow-up

More than an "error code", this is what is lit and displayed from left to right on the control panel:

Filter Reset: Red light is lit (though not due to be changed)
Freezer Temp: locked at -88
Express Freeze - symbol is lit
Frig Temp: locked at 88 (although temp is freezing stuff now)
Lock: Red light is lit (press&hold to unlock does not work)

Posted by on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
bbtoast

Brian Berndt

  • 319 Answers

SOURCE: Sears Trio model 795.75546400 error message: -88 * 88

As to the 88 display, there is one thing to try but it is a longshot:

Try to press the Energy Saver and Freezer temp buttons at the same time for 5 seconds, see what happens.

The 88 is not a used error code.

If that does not work then, I believe that Sears will be replacing your main board (motherboard)for this unit, as it sounds like it is bad.

Sorry for your trouble!

Brian

Posted on Aug 04, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The fuser error light is on and my Xerox XC 1040 copier will not work. There is no error codes displayed


The drum light can be reset via the control panel. Especially if your copies were good before the light came on. The drum unit is the cartridge that is located right next to the toner cartridge. Reset the light using the following reset procedure:
To reset the drum light on just about any Xerox XC or XD series copier press the following key's in sequence and as quickly as possible (with 4 seconds for the first 4 keys)
Press "C" then the far left key (exposure mode) then the "C" key then the far left again.
So in other words C, far left, C, far left
If done correctly the display should go blank.
Then key in 24 as if you were going to make 24 copies.
Now press the "print" button
Now key in 7 as if you were making 7 copies
Now press the print button again.
You should now be getting flashing zero's on the display.
Turn the machine off then on again and your drum light should be gone!
You can usually reset this counter at least once to get twice the life out of your drum unit.
Good Luck and Thank You for using Fixya.
WheatlandServices

Nov 12, 2010 | Xerox Office Equipment & Supplies

1 Answer

Have a 1999 John Deere Dozer 650G LGP series and on the control panel where you crank the engine there are four lights to the left of the key ignition switch about dime size. Starting from left to right...


Check your hydraulic filter,if it has not been replaced in a while the filter may have a restriction allowing the light to illuminate. The red light may be telling you there is not enough flow through the filter to operate safely with out doing damage to the hydarulic system.

Dec 13, 2009 | Garden

1 Answer

Help....kenmore trio refrigerator, error message "er co"


The Er Co error code signifies a communication error between the display control board on the freezer door and the main power board on the outer back panel of the refrigerator.

Check the wiring and connections between the low voltage interface and the main high voltage board.

If you are able to unplug the refrigerator and remove the cover over the control board on the back of the refrigerator,
you can check the wiring connection on the main control board.

If this wiring connection is okay, check the wire harness connection under the hinge cover on the top of the left hand refrigerator door.
If these connections are okay, then you will need access the wire harness connection in the dispenser.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Mar 19, 2009 | Kenmore 73502 / 73504 / 73509 Bottom...

1 Answer

Red light is always on


f the Drum LED is still lit after replacing the drum unit, the Drum counter may not be reset.
Reset the Drum counter as follows:

  1. Open the front cover.
  2. Locate the control panel button under the LED lights on the left side.
  3. Press the control panel button until all lights are lit, then release it.
    The Drum counter is now reset.

Aug 14, 2008 | Brother HL-2040 Laser Printer

1 Answer

XC-830 copier Displays fault code H-3


Give this a try , if it continues you will have to replace the fuser.

Performing a Fault Reset 14 will reset your copier and will help to clear error codes.
  1. Turn the power off.
  2. Locate the Clear Button, which is grey in color, in the upper right corner above the green Start Button.
  3. Locate the Auto Button the lower left corner of the Control Panel.
  4. Turn the power back on.
  5. Press the buttons in the following sequence, releasing each button after each time you press it: [Clear], [Auto], [Clear], [Auto]. Every light on the Control Panel should go out, and the error code should clear.
  6. If the error code has not cleared, wait a few seconds then repeat Steps 1 through 5.
  7. Program the copier as if you were going to make 14 copies.
  8. Press the green [Start] button to store the reset code. The copier will return to the ready position.
  9. Run a test copy

Aug 07, 2008 | Xerox Office Equipment & Supplies

2 Answers

Error code


NOTE: Some Status codes will not clear even though the problem has been fixed. Status codes that will not clear must be manually reset using the 'Fault Reset 14 Procedure'.
  1. Locate the [C] (Clear) button on the Control Panel, at the far right.
  2. Locate the Image Quality button, below the Auto on the Control Panel, toward the left side.
  3. Press the buttons in the following sequence within 4 seconds. Press [C] (Clear), press [Image Quality], press [C] (Clear) again, press [Image Quality] again.
  4. The error code should disappear. If the Status code does not clear, repeat step 3 until the status code clears; but no more than five times.
  5. Use the [10] and [1] buttons to enter 14 on the Display Screen, as if you were to make 14 copies.
  6. Press the [Start] button. The machine should be ready to use.
  7. Make a copy, to check that the machine is working properly

May 18, 2008 | Xerox WorkCentre PE16 All-In-One Laser...

1 Answer

Trouble code


NOTE: Some Status codes will not clear even though the problem has been fixed. Status codes that will not clear must be manually reset using the 'Fault Reset 14 Procedure'.
  1. Locate the [C] (Clear) button on the Control Panel, at the far right.
  2. Locate the Image Quality button, below the Auto on the Control Panel, toward the left side.
  3. Press the buttons in the following sequence within 4 seconds. Press [C] (Clear), press [Image Quality], press [C] (Clear) again, press [Image Quality] again.
  4. The error code should disappear. If the Status code does not clear, repeat step 3 until the status code clears; but no more than five times.
  5. Use the [10] and [1] buttons to enter 14 on the Display Screen, as if you were to make 14 copies.
  6. Press the [Start] button. The machine should be ready to use.
  7. Make a copy, to check that the machine is working properly.

May 06, 2008 | Sharp AR-160 Copier

1 Answer

Xerox Workcentre Pro 215


This should resolve that fault code


NOTE: Some Status codes will not clear even though the problem has been fixed. Status codes that will not clear must be manually reset using the 'Fault Reset 14 Procedure'.
  1. Locate the [C] (Clear) button on the Control Panel, at the far right.
  2. Locate the Image Quality button, below the Auto on the Control Panel, toward the left side.
  3. Press the buttons in the following sequence within 4 seconds. Press [C] (Clear), press [Image Quality], press [C] (Clear) again, press [Image Quality] again.
  4. The error code should disappear. If the Status code does not clear, repeat step 3 until the status code clears; but no more than five times.
  5. Use the [10] and [1] buttons to enter 14 on the Display Screen, as if you were to make 14 copies.
  6. Press the [Start] button. The machine should be ready to use.
  7. Make a copy, to check that the machine is working properly

Jan 24, 2008 | Xerox WorkCentre PRO-215 All-In-One Laser...

1 Answer

SHARP AR-M277


this should resolve it.

NOTE: Some Status codes will not clear even though the problem has been fixed. Status codes that will not clear must be manually reset using the 'Fault Reset 14 Procedure'.
  1. Locate the [C] (Clear) button on the Control Panel, at the far right.
  2. Locate the Image Quality button, below the Auto on the Control Panel, toward the left side.
  3. Press the buttons in the following sequence within 4 seconds. Press [C] (Clear), press [Image Quality], press [C] (Clear) again, press [Image Quality] again.
  4. The error code should disappear. If the Status code does not clear, repeat step 3 until the status code clears; but no more than five times.
  5. Use the [10] and [1] buttons to enter 14 on the Display Screen, as if you were to make 14 copies.
  6. Press the [Start] button. The machine should be ready to use.
  7. Make a copy, to check that the machine is working properly.
elem_1_spacer.gif

Jan 22, 2008 | Sharp AL-1655CS Laser Printer

1 Answer

Brother HL 2040 problem


if the Drum LED is still lit after replacing the drum unit, the Drum counter may not be reset.
Reset the Drum counter as follows:

  1. Open the front cover.
  2. Locate the control panel button under the LED lights on the left side.
  3. Press the control panel button until all lights are lit, then release it.
    The Drum counter is now reset.

Sep 14, 2007 | Brother HL 5250DN Laser Printer

Not finding what you are looking for?
Kenmore 73502 / 73504 / 73509 Bottom Freezer Refrigerator Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Refrigerators Experts

Jimmy

Level 2 Expert

61 Answers

geob91

Level 2 Expert

128 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Are you a Kenmore Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...