Question about Mintek DVD-1600 DVD Player

2 Answers

Device code for mintek dvd. No code for mintek dvd in my user guide for dish network to control power for dvd on my dish remote.

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 246 Answers

Hi my nameis Mike Houston of DISH Network and I see where you want the code for theMintek DVD-1600 to program to the DISH Network remote. We currently do not have any codes for theMintek DVD player; I will send a link to help with a Power Scan, http://www.dishnetwork.com/SupportSection/power-scan-instructions.

Posted on May 03, 2011

Ad

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 185 Answers

You may want to search for the code by performing a Power Scan, I will include the steps below. If this doesn't resolve this there is most likely a compatibility issue.
Power Scan:
1.) Press and hold the correct VCR button (about six seconds) until all mode button backlights come on, then release.
2.) Press 500 pound (#)
3.) With the desired equipment on, press and hold the VCR/DVD button until all mode button backlights illuminate (about 3 seconds), then release.
4.) Press and release the Power button.
5.) Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off.
6.) Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.
To verify the code works try several different functions for that equipment.

Daniel Busa
DISH Network
Customer Service

Posted on May 03, 2011

  • Karina Anguiano Oct 13, 2011

    are the buttons in step 1 and 3 the same button because that is what I understood but you do refer to buttons differently and I'd like to be sure b4 I try this. -k

×

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We need the code to type in to control the power on our dish network remote.


Hi my nameis Mike Houston of DISH Network and I see you need the code for the Mintek DVDplayer. We currently do not have a code that goes to the DISH Network remote, wedo have what we call a Power Scan to program the DISH remote to the DVD player.I will send the link to help with these steps, http://www.dishnetwork.com/SupportSection/power-scan-instructions.

May 01, 2011 | Mintek DVD-2580 DVD Player

Tip

Dish Network User, Remote Code and HD Manauls


All Dish Network Manuals can be found at this link. Just click below to find your Dish Network remote codes, user manual and HD Guides.<br /><br /><a href="http://www.dishnetwork.com/supportsection/manuals">http://www.dishnetwork.com/supportsection/manuals </a>

on May 29, 2011 | Televison & Video

1 Answer

Trying to set up dish network remot to apex dvd player


dr172120,

I'm sorry you are having problems programming your DISH Network remote to your Apex DVD player. I looked through our remote codes but I don't show we have a code for an Apex DVD player. We do have remote codes for an Apex TV. You can run a power scan to see if you can find a code for the DVD player. I have provided the instructions to conduct the power scan below. If you have any other question, please post to this site.

Ray Calo
DISH Network - Executive Offices

Address To Other Equipment Using Power Scan
  • Remote: All Remotes (except Basic)
    1. With the desired equipment on, press and hold the correct Mode button until all mode button backlights illuminate, then release.
    2. Press and release the Power button. AUX Mode: Before pressing and releasing the Power button
      • Press 0 for a TV
      • Press 1 for a VCR/DVD
      • Press 2 for any other device.
      Then Press STAR (*)
    3. Press the Up button once a second while pointing the remote at the desired equipment. Note: If the code for the equipment comes up, the equipment will power off.
    4. Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.

Jan 14, 2011 | DISH Network IR Remote Control

2 Answers

How to use your control with my dvd player


Hello chegui59, my name is Michael Hurst with DISH Network. There are 2 ways of programming your remote to your DVD player. You can use a remote code for your DVD player. In order to give you the right remote code I would need to know the manufacture of your DVD player and the model of the remote that you have. You can also try a Power Scan to get the DVD player programmed into your DISH remote, here are the steps: Withthe desired equipment on, press and hold the correct mode button until all modebutton backlights illuminate, then release. Press and release the Power button. AUX Mode: Before pressingand releasing the Power button. Press 0 for a TV, Press 1 for a VCR/DVD andPress 2 for any other device. Then Press STAR (*). Press the Up button once asecond while pointing the remote at the desired equipment. If the code for theequipment comes up, the equipment will power off. Press the POUND (#) button. Ifthe code entered is valid for the remote, the mode light flashes three times.

May 29, 2010 | DISH Network IR Remote Control

1 Answer

I have dish network and a new rca tv with dvd the


You can power scan for the code.
Turn ON the electronic device you want to program the remote to control.
Press the Mode button( sat,tv,dvd,aux) on the remote until the appropriate mode light is flashing.

Press the Power button. The mode light will stop flashing and stay lit.
Press the Up or Down arrow button to set the remote to the next code. The Down arrow button scans backward and the Up arrow button scans forward.
When the correct code is reached, the device (whether a TV, VCR, or other) will turn off.

Press the pound key button to store the code in the remote control memory. If the code is valid for your remote, the mode light will blink 3 times.
Turn the device back ON by pressing the Power button.
Press sat mode key once you power back on the tv to be able to operate the receiver box.
Try some other functions to make sure you have the correct code. Occasionally the Power button may work when others do not.
If the other buttons work you are finished.

.
If the other buttons do not work, repeat the previous steps. The scan will resume from the last code stored.
The mode light will flash rapidly when the scan has returned to the starting point and all codes have been tested for that mode. The remote control may not control some device models.

Mar 11, 2010 | DISH Network 322 DTV Receiver

1 Answer

Remote does not work even after putting in the codes from the uses's guide


You can try a power scan:

    1. Verify the remote is a DISH Network remote. Look for the DISH Network logo on the bottom of the remote and Mode buttons or lights at the top.

    2. We do have the codes for all DISH Network remotes and would be happy to help you with your DISH Network manufactured remote. Please contact the manufacturer of your remote for further assistance. Detailed instructions may be included in the owners' manual that came with your equipment. If not, there may be a toll-free technical support number listed.

    1. With the desired equipment on, press and hold the correct Mode button until all mode button backlights illuminate (about 3 seconds), then release.
    2. For AUX mode Power Scan ONLY: press 0 for a TV, press 1 for a VCR/DVD, press 2 for any other device, then press *.
    3. Press and release the Power button.
    4. Press the Up button once a second while pointing the remote at the desired equipment. If the code for the equipment comes up, the equipment will power off.
    5. Press the POUND (#) button. If the code entered is valid for the remote, the mode light flashes three times.
    6. To verify the code works have the customer try several different functions for that equipment.

    Oct 29, 2009 | DISH Network 135899 Remote Control

    1 Answer

    Need Dish Network Code for Sony DAVHDX275 Audio System


    Refer to page 82 in your Dish Network User's Guide......(Make sure Sony system is powered on and in DVD mode with a disc in the player).  Point Dish remote at Sony box -  Hold Aux until all buttons light up at top....press 2 - then STAR button* and then POWER button - then press the up arrow key repeatedly until Sony turns off - press # key to lock in code.
    It took me awhile to get it to work....it will only work power, mute, and volume - not dvd play functions. Refer to page 85 to make the Dish remote control the Sony box volume by default.
    Good luck.

    Jan 25, 2009 | Sony BRAVIA DAV-HDX267W Theater System...

    4 Answers

    Dish Network remote code for RCA 20F510TD TV/DVD


    hello and please help.
    want to know the codes and way to program this rca dish remote model RCR500SAM1 for my Toshiba tv.
    ive done it a few years ago but forgot.
    so i need the codes for toshiba tv and way to program this rca dish network remote.
    grateful,
    kay

    Jul 26, 2008 | RCA 20F510TD 20 in. TV/DVD Combo

    1 Answer

    Remote control code for Philips VCR & DVD player DVP3340V/17


    If you have Dish Network and I suspect if you have Direct TV or a cable providers, you can use your remote for that service provider to find your VCR code. For the Dish you can look in the user's guide on pages 9 and 19 to see how to do a "Device Code Scan" and "Check Device Code".
    To Scan: #1: Turn on the device you wish to scan for a code, #2 Press and hold down the button on your Dish remote for that device until all the buttons light up and the specific device button is flashing, #3 Press the blank power button, #4 press the up or down button until until your VCR tuns off, #5 Press the POUND ( # ) key to store the code number and #6 Press the blank power key to turn the device back on.
    To Check the Device Code: #1 Press and hold down the device key until all buttons light up and the device button is flashing, next press the POUND ( # ) key TWICE ! The Mode button will flash to code number with a pause between each number, i.e. 5 flashes, pause 3 flaskes, pause one quick flash is 530. Write down this number and you are rady to go !

    Nov 16, 2007 | Televison & Video

    6 Answers

    Remote control code for magnavox dvd/vcr combo


    I need codes for my Universal Philips Magnavox remote for a Sanyodvd vcr combo ?

    Sep 07, 2007 | Philips Magnavox Learning Universal Remote

    Not finding what you are looking for?
    Mintek DVD-1600 DVD Player Logo

    193 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mintek Televison & Video Experts

    Ekse

    Level 3 Expert

    13434 Answers

    Brad Brown

    Level 3 Expert

    18121 Answers

    The Knight
    The Knight

    Level 3 Expert

    76177 Answers

    Are you a Mintek Televison and Video Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...