Question about GE ADW1100N Built-in Dishwasher

1 Answer

I have a 15 month old ADW 1100N dishwasher that all of a sudden stopped spraying water during cycles . I checked the feed water line and it is not restricted.

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

Make sure the spray arms are not clogged with food scraps too

Posted on Jun 07, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my dishwasher stop during cycles and the cycle light blinks?


it has few functions , so break them down to this.
does water flow in correctly . hot an cold
does the pump re-cycle water well inside . reflow lots of spray.
then does it pump out correctly an flow easily into garbage disposal , check the back flow valve for stoppage if it has one {its in the large plastic pipe right before the disposal.lets water flow but compactor garbage is blocked, it sticks a lot closed }
and is the door latch secure test it by opening suddenly is all you can do.
you might have to open the door quickly to check these items like spray or pumping.

Aug 03, 2014 | Whirlpool Gold Dishwasher with Quiet...

1 Answer

Spray arms not working


Hi frustrated in Raleigh,
I understand that the spray arms are not moving or spraying water, even after you have cleaned the screens and arms. What might be happening is you are not getting enough water pressure to the dishwasher.
The hot water line to your dishwasher must provide water pressure between 20 and 120 psi.
Low water pressure may occur when laundry or showers are in operation.
Wait until water use is reduced before starting dishwasher.
If you are still noticing that the spray arms are not moving or spraying water, I would have a local Authorized Technician come out to see what exactly is going on with the spray arms of your dishwasher.

-Best Regards-

Jan 06, 2014 | Frigidaire FPHD2491KF Dishwasher

1 Answer

We have an asko 3530 dishwasher that is 4 to 5 years old now and when we run any wash cycle some time during the cycle we get an error that that says water inlet fault. Is there a filter or something we...


Some do have a screen but most don't. It could be possible that your feed line may be kinked? There is also the valve at the water inlet that could possibly going bad as well. Hope this helps.

Jun 07, 2017 | Asko Dishwashers

3 Answers

The dishwasher seems to be cycling - but I no longer get the flush into my disposal and I don't hear much water circulating inside the machine. Also, the soap doesn't all diappear. Any suggestions?


The high pressure water pump is defective and is not spraying the much required jets of water to the dishes.
This is the reason that your dishes are also not cleaned.
You might have to remove and check if the pump is faulty or a cleaning job can rectify the issue.

Sep 11, 2010 | KitchenAid KUDS03FTBL Dishwasher

1 Answer

Dishwasher is not cleaning dishes


Hi,


I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...

Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101


k

Apr 14, 2010 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

The dish washer is taking ages to wash and it not clean ing dishes well


ok so If your dishwasher has worked fine in the past but, suddenly, your dishes aren't clean after the dishwasher completes all cycles:
1) Check your water heater's temperature dial to be sure it hasn't been changed recently.
2) Be sure dishes haven't prevented the detergent dispenser from opening properly during the wash cycles or kept the spray arms from turning, the lower arm from rising, or the spray from reaching the upper rack's dishes.
3) During the wash cycle, listen to the spray arm spinning inside. If it seems to be spinning poorly, clean out the spray holes in the spray arm(s) with a stiff piece of wire; wait for the machine to cool, and then remove the spray arm(s) by unscrewing the hub cap and lifting the arm(s) off
Regards Gizokieth

Sep 10, 2009 | Dishwashers

1 Answer

GE Dishwasher - poor cleaning


I believe there is a screen/filter on the water line before or at the water fill valve. If that gets plugged it can restrict the flow. The fill valve can also fail/get plugged and restrict the flow.
Also, dishwashers usually have a level sensor to tell when there is enough water to do the wash. It may be a float inside the tub that operates a mechanical switch or it may have a hose to a pressure sensor. Either type can get greasy/dirty/plugged and as a result cause improper water levels.
Check both the water supply filter/fill valve and the level sensor. One or both of those may be involved.

Mar 10, 2017 | Kenmore Dishwashers

1 Answer

Dishwasher cycles but does not clean the dishes


if your dishwasher is cleaning poorly, check these: Water-inlet valve Most cleaning problems are caused by the dishwasher not getting enough wash water, so the water-inlet valve is often to blame. This valve is usually at the bottom left or right of the dishwasher, behind the lower access panel. It's the device with the main water line from the house, a rubber tube to the dishwasher, and two wires attached to it. 

When a water-inlet valve is defective, you may hear the sound that's usually referred to as "water hammer." If the water-inlet valve is defective, you need to completely replace it. 

Dishwasher Water Inlet Valve Replacement

Be sure to read and understand any instructions that come with the new water inlet valve.

Tools required: 

Adjustable wrench

Multi-Screwdriver 

Pliers 

Step 1. Disconnect the dishwasher from its power source. 

Note: Dishwashers are usually wired directly to the home’s electrical system. To disconnect the power, switch off the circuit breaker or remove the fuse for the electrical circuit the dishwasher is attached to. Try to turn the unit on after disconnecting the power to be sure you were successful. 

CAUTION: If you’re not sure you’ve shut off the power properly, DO NOT CONTINUE. Call a qualified appliance repair technician to complete the repair. 

Step 2. Turn off the water supply to the dishwasher. This is usually underneath the kitchen sink or in the basement or crawlspace near the location of the dishwasher. Pliers may be helpful here. 

Note: If there are no shut-off valves, you must shut the water off at the main water supply valve for your home. 

Step 3. Remove the lower panel(s) of the dishwasher. These are usually held by 2 to 4 screws at the upper and lower corners of the panel(s). 

The inlet valve is usually near the front of the dishwasher. Attached to the valve you’ll see: 2 or 4 wires, the water supply line from the house and the water feed line that goes to the dishwasher. 

Step 4. Remove the household water supply line from the valve. The line is usually secured with a brass compression nut. The water supply line is usually copper or braided stainless steel. 

CAUTION: Water supply line may be hot. 

Step 5. Remove the fitting from the valve the water supply line was attached to. This fitting may be very difficult to remove. It may help to put the valve into a vice in order to remove the fitting. If you cannot remove it, replace it. The fitting is not an appliance part but a plumbing part that is available at most hardware stores.

Step 6. Remove the screws holding the valve to the dishwasher frame. 

Step 7. Label the wires to the valve so you’ll be sure to reattach them correctly. 

Step 8. Remove the wires from the valve. 

Step 9. Remove the clamp on the black rubber water discharge tube and pull the tube off of the valve. 

Step 10. Reinstall the old fitting (or a replacement fitting if necessary) onto the new valve the water supply line was attached to. Use Teflon tape or pipe joint compound as a thread sealant. Make this fitting tight to prevent leaks. Make sure that the fitting points in the same direction as the old one so that the water supply line will meet up with it properly. 

Step 11. Install the new valve in the reverse order of the removal instructions. 

Note: The water supply line is under high pressure. Be sure to tighten the fittings properly. 

Step 12. Turn on the water to the machine, and check for and correct any leaks. 

Step 13. Reinstall the access panel(s). Restore the power to the dishwasher and test. 

Note: You may have to let the dishwasher run a few minutes before it reaches the next water fill cycle. 

Internal filters Every dishwasher has some type of filter to keep large food particles and foreign objects away from the pump assembly:

  • Most modern dishwashers have self-cleaning filters that don't need any routine cleaning.


  • Some have filters in the bottom of the dishwasher that you need to periodically clean. You don't need any tools to remove the filter, and cleaning it is easy. Consult your owner's manual to determine which type you have and its maintenance requirements.


If your filter is clogged, it may be causing the cleaning problem. 

Drain valve Some dishwashers have a valve (or gate) that should open only during draining. If debris lodges in the valve, it can't close properly, so water drains out during the wash cycle. Most dishwashers drain into the garbage disposer. If yours does that, listen for water flowing into the disposer during the wash cycle. If you can hear it then, the drain valve may be clogged.

Spray arms There's a spray arm at the bottom of your dishwasher--it may have a tall spray tube mounted to the center of it. There may also be a spray arm located directly beneath the upper rack of dishes and/or above the upper rack.

If debris is blocking the holes in the spray arms where the water comes out, it could cause cleaning problems. Regularly inspect each of the spray arms and clean out the holes as necessary. 

Water temperature To get the best cleaning results, the water entering your dishwasher needs to be hot enough. Try running the hot water in your kitchen sink for about 30 seconds before starting the dishwasher, to pre-heat it. Also, if your dishwasher lets you select a higher wash or rinse temperature, try that to see if it helps. 

To check the temperature of the hot water that comes from your kitchen faucet use a waterproof thermometer. If the water isn't 120 degrees Fahrenheit, your dishwasher may have trouble getting your dishes clean. You could increase the temperature of the hot water to the whole house--and therefore the dishwasher--by adjusting the hot water heater thermostat.

Warning! To lessen the risk of scalding, don't set the hot water heater temperature higher than 120 degrees Fahrenheit. 

Detergent cup Dishwashers don't perform their best if detergent is introduced only at the beginning of a cycle, so add detergent to both parts of the cup. 

Nov 08, 2008 | GE Nautilus 24" Built-in Dishwasher

Not finding what you are looking for?
GE ADW1100N Built-in Dishwasher Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike

Level 3 Expert

4363 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...