Question about Mitsubishi Mr. Slim MXZ30TN Air Conditioner

1 Answer

After power cut aiconditioner turns on then standby message comes on next to heater icon and then airflow stops , unit stays on but no airflow

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers
Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Harman Kardon AVR 350, Unit powers off into standby mode after a few seconds. Removed all connections and wires, problem persists. Weirdly enough, if I keep pressing the source button, the unit stays on....


It needs to be serviced. Bad caps, resistors, & possibly a transistor or two. Not an unbearable repair, but you can count on it being 100-175 depending on the shop. You followed all the troubleshooting you could without opening the unit.

Oct 02, 2013 | Marantz SR8001

1 Answer

Have a gmp125-4 furance blower runs all the time checked themostat wires error code 1 blink then 2 then 3 then 5 furance works if you turn power off turn back on when heat kickes off blower comes on gives...


Sounds like limit switch issue. Furnace heats up, high temp limit switch opens, fan will stay on. GMP model is older and do not have the codes.
May be over fired, have airflow problem, to cause the limit to open.
Next time before shutting off power, try to find the limit, it has two wires that connect to a 1.5 x 2 inch card mount to the furnace fire wall. tap on it and see if the blower stops. If so replace the limit.

Sep 06, 2011 | Goodman Heating & Cooling

1 Answer

Our Teac hdr2500t epg Guide stopped working showing only the programme times but not titles. This comes only a couple of days after it stopped allowing me to watch one programme while recording another...


Turn off the unit via the standby button on the remote and pick "passive standby". Next time you turn it on the epg will be back. The other option is to turn off the unit via the power switch at the rear of the unit.

Jun 29, 2010 | Televison & Video

2 Answers

The hot water will not come on intermitently. I


if your on a private well, it sounds as though your loosing enough water pressure to shut the heater off,.(which is right before the water pump comes on),....tankless heaters turn on by sensing water flow, and of course off when flo stops,......water pressure tanks often need to be re-charged with air for pressure to stay even,....does your water pressure fluctuate?

Jan 10, 2010 | Rheem EcoSense by 7.4 GPM Tankless Water...

1 Answer

Honeywell HZ-705.....HELP!!!!


Should have oil in it. I don't think you can refill it. If it has leaked out, it's probably no good. Anyway, here are the instructions.


Press the *power button* once to start the heater on high power, continuous run. If left at this setting, the unit will run continuously on high power (1500 watts, 12.5 amps) and will not shut off until the unit is manually turned off.
Press the *power button* again, to change to low power, continuous run, (900 watts, 7.5 amps) and will not shut off until the unit is manually turned off.

Set temperature:

Press the temp/timer button until the temperature icon blinks. Use the up and down arrows to set the desired temperature.
The temperature icon will stop blinking and the current room temperature will reappear after the desired temperature is set.

The heater will turn off and on to achieve the desired temperature.

Set timer: (auto off)

Press the timer/timer button until the timer icon blinks. The hour display will appear. The auto off icon will also appear.
Use the up and down arrow buttons to set the heater operation time between 1 and 10 hours. This function will activate once the timer icon stops blinking. The heater will automatically turn off whn the times runs out.

Set timer: (auto on)

Press the temp/timer button until the timer icon blinks. The hour display will appear. The auto on icon will also appear.
Use the up and down arrow buttons to set the heater start time between 1 and 10 hours. This function will activate once the timer icon stops blinking.
The heater will automatically turn on when time expires.

Hope this helps!

Aug 17, 2008 | Heating & Cooling

1 Answer

Orange light on lamp icon on Optoma EP732H Projector


This same thing happened to me, I removed the bulb and put it back in, it reset something and I was able to use the projector again.

Nov 12, 2007 | Optoma EP732H EZPRO DIGITAL PROJECTOR...

1 Answer

Honeywell oil radiator


Press the *power button* once to start the heater on high power, continuous run. If left at this setting, the unit will run continuously on high power (1500 watts, 12.5 amps) and will not shut off until the unit is manually turned off.
Press the *power button* again, to change to low power, continuous run, (900 watts, 7.5 amps) and will not shut off until the unit is manually turned off.

Set temperature:

Press the temp/timer button until the temperature icon blinks. Use the up and down arrows to set the desired temperature.
The temperature icon will stop blinking and the current room temperature will reappear after the desired temperature is set.

The heater will turn off and on to achieve the desired temperature.

Set timer: (auto off)

Press the timer/timer button until the timer icon blinks. The hour display will appear. The auto off icon will also appear.
Use the up and down arrow buttons to set the heater operation time between 1 and 10 hours. This function will activate once the timer icon stops blinking. The heater will automatically turn off whn the times runs out.

Set timer: (auto on)

Press the temp/timer button until the timer icon blinks. The hour display will appear. The auto on icon will also appear.
Use the up and down arrow buttons to set the heater start time between 1 and 10 hours. This function will activate once the timer icon stops blinking.
The heater will automatically turn on when time expires.

Hope this helps!

Sep 24, 2007 | Honeywell /KAZ HOME ENVIRONME HZ-705 7Fin...

Not finding what you are looking for?
Mitsubishi Mr. Slim MXZ30TN Air Conditioner Logo

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Heating & Cooling Experts

NOEL
NOEL

Level 3 Expert

8537 Answers

vince

Level 3 Expert

1234 Answers

Stuart Slabber

Level 1 Expert

25 Answers

Are you a Mitsubishi Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...