Question about HP LaserJet 3330 All-In-One Printer

Open Question

My hp 3330 printer says ready but won't print. I rebooted computer, unplugged printer for 10 seconds, tried troubleshooting, won't print!

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: HP laserjet 3330 MFP

It will eventually reset itself, usually after being unplugged for an hour or so, but the error will return regularly. There are several posts all over the place on this error, but it seems that it is seldom solved, without replacing the scanner unit (entire top of machine) - which is obviously not worth the hassle/expense. Just seems to be a common problem with this family of machines

Posted on May 17, 2009

Ad

Anonymous

  • 80 Answers

SOURCE: printer is printing two smudge marks on my documents.

Two parts of the printer can affect this.
1) the toner cartridge
2) the fuser

Testing can be done to determine the problematic part.

Do a print using manual feed. Once the last bit of paper goes into the machine, open the printer door.
Remove the toner to check if smudge is there.
Replace toner cartridge if there is smudge, replace fuser it not.

Posted on May 29, 2009

Kenneth Brilliant

  • 39 Answers

SOURCE: My printer gets stuck on initializing...or

After you power on the printer, does it ALWAYS do calibration, and if so, does the calibration cycle complete or just goes on and on?
From your description, it sounds like the printer will come to the READY ... eventually after calibration. That's a good sign. The fact that it does not print could be other factors.
1. first, get a high speed parallel cable and hook the printer directly up to your computer. Be sure your commnications are good.
1a. if you only have ethernet connection to the printer, then you'll need to print out the information page so that you can find the IP address of the printer. If the printer's IP address shows all zeros, then the IP address for the printer's jet direct card has not been defined. Instead of going on about how to install a new port, drivers, etc. please tell me where you're at.

Posted on Feb 19, 2010

decso

decso

  • 20 Answers

SOURCE: blinking/flashing lights(orange & green) &

that is because ur head of ur printing cartridge is damaged.

remove ur cartridges black as well as color
n install only black cartridge n check d blinking of lights on ur printer if it doesn't blinks it's mean ur black cartridge is OK but ur blinking of light on ur printer is same it's mean ur head of black cartridge is damaged
after this process remove the black one cartridge and install the color one cartridge n check d blinking of lights on ur printer if it doesn't blinks it's mean ur color cartridge is OK but ur blinking of light on ur printer is same it's mean ur head of color cartridge is damaged
now take a dry cotton cloth n gently clean ur cartridges head install both cartridges on ur printer n check ur blinking light on ur printer that will work only if u r too lucky other wise u have to purchase a one cartridge.

Posted on May 29, 2011

TabTreeJunki

  • 1 Answer

SOURCE: My HP Officejet 6500 Wireless

I also have the OfficeJet 6500 and had the same problem. The black text was printing using a mix of colored inks instead of the black ink, resulting in a grey, fuzzy text. I finally found a solution. In each application under Page Setup, there is an option called "Format for". Mine had been set to "Any Printer". I changed that to "Officejet 6500 E709n [830E4A]" and now it prints the black just fine. I have a Mac running 10.4.11. Hope this helps.

Posted on Jun 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My HP F4280 says it's printing but the pages come out blank. How do I get them to really print??


uninstall the reinstall the driver for the printer from the HP web site for that printer and the win operating system you are using

Jan 01, 2018 | HP DeskJet F4280 All In One Printer InkJet

1 Answer

Why won't my printer print after I installed the software? It says its ready but nothing will print


A quick fix for most communication errors can be achieved by resetting the printer and/or rebooting the PC. Simply disconnect the printer from your computer. Reboot your pc. Unplug and re-plug the printer into the power source to reset it. When the printer turns on, reconnect it to your computer. Then try to print again once the computer fully recognizes the USB connection.


If that doesn't help, try the steps below:

1. Disconnect the printer from your computer.

2. Rebrick (pull out power supply, black box where the power cord is plugged in at the back of the printer, and put it back after 30 seconds).

2. On your computer, go to Control Panel > Printers and Faxes.

3. Delete the Lexmark print object.

4. Reboot your pc.

5. When your pc turns on, reconnect the printer.

6. Wait until your pc fully recognizes the USB connection. To check, go to Control Panel > Printers and Faxes. If you see a new Lexmark print object in the list, then try to print/scan again.

Aug 18, 2011 | Lexmark PhotoJet Z705 InkJet Printer

1 Answer

Hi - I have HP Laserjet 1200 printer -- today the printer will not print -- print que says "Ready" -- no items are in que -- I have rebooted computer as well as unplugged printer but still not printing --...


check the usb cable or its port ,or try print a test page from the printer by pressing front pannel button 5 second and release. if printng a test pasge its ok the printer

Feb 10, 2010 | HP LaserJet 1200 Printer

1 Answer

HP laserjet 3330 keeps flashing scanner error power off. I unplug and start again. It will print and then goes back to this same thing.


Hi,
Remove and replace the power cord from the unit.

Wait approximately for 35 seconds for the scanning assembly to "walk out"(move to ready position)and then quickly remove the plug again.

Repeat step 1 and 2,three or four times until the head (scanner lamps)moves approximately 1 inch away from its normal resting place.

Replace the plug and let the product fully finish the boot cycle.
If it does not resolve the issue or the issue returns,upgrade the product firmware may help.Visit this url http://h20000.www2.hp.com/bizsupport/TechSupport/DriverDownload.jsp?prodNameId=72628&lang=en&cc=us&prodTypeId=18972&prodSeriesId=66359&taskId=135
and then upgrade the firmware.

Feb 10, 2010 | HP LaserJet 3330 All-In-One Printer

1 Answer

79 error


hI
Ok try this it will some times work
A solution:
  • Unplug
  • Hold down "*" & "enter/ menu buttons"
  • While holding down both buttons, turn power on
  • Wait until something like "initialize" shows up on the display
  • Let go of buttons
  • Wait until display reads "ready"
  • Unplug for 10 seconds, then plug back in
Let us know if it works for you
All The Best: Pineworks

Jan 27, 2010 | HP LaserJet 3330 All-In-One Printer

1 Answer

Error 79 what is it


Hi
You can try
A solution:
  • Unplug
  • Hold down "*" & "enter/ menu buttons"
  • While holding down both buttons, turn power on
  • Wait until something like "initialize" shows up on the display
  • Let go of buttons
  • Wait until display reads "ready"
  • Unplug for 10 seconds, then plug back in
  • Please let me know if it works so I can pass it on to some one eles All The Best: Pineworks

Jan 12, 2010 | HP LaserJet 3330 All-In-One Printer

1 Answer

79 error displayed power on power off and the


Hi
I can only say try it may work.
A solution:
  • Unplug
  • Hold down "*" & "enter/ menu buttons"
  • While holding down both buttons, turn power on
  • Wait until something like "initialize" shows up on the display
  • Let go of buttons
  • Wait until display reads "ready"
  • Unplug for 10 seconds, then plug back in
  • Please let me know if works for you.
  • All The Best Pineworks

Jan 11, 2010 | HP LaserJet 3330 All-In-One Printer

2 Answers

After getting error 79 won't print


A solution:
  • Unplug
  • Hold down "*" & "enter/ menu buttons"
  • While holding down both buttons, turn power on
  • Wait until something like "initialize" shows up on the display
  • Let go of buttons
  • Wait until display reads "ready"
  • Unplug for 10 seconds, then plug back in
  • Hope it works for you

Apr 24, 2009 | HP LaserJet 3330 All-In-One Printer

Not finding what you are looking for?
HP LaserJet 3330 All-In-One Printer Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Cindy Wells

Level 3 Expert

6065 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...