Question about Bosch TKA 9110 Coffee Maker

1 Answer

Bosch porsche 9110 drip coffee maker

The filter basket dropped and plastic pieces holding spring broke off.  where can i purchase a replacement?

Posted by on

  • nastia9 Apr 01, 2009

    the filter basket dropped and plastic pieces holding spring broke off. where can i purchase a replacement?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mine just broke this morning! i just ordered the same part from appliancepartspros.com - the part number is AP2807555. It is currently backordered until 4/25/09 - hopefully I will get that and the other part I ordered. Hope this helps.

Posted on Apr 15, 2009

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a Mr Coffee model #BVMC-PSTX91. The filter basket has a spring loaded release that has fallen off - how do I put back on? cannot figure out how to put the spring and extra plastic piece on?


without seeing it (a picture) that is a difficult question to respond to. it may have possibly broken or a piece of plastic needed to keep it in place broke - or the spring is defective. suggest get a new basket. (or go to the store, or find a neighbor with a similar model - and look at his basket, take a pic of the spring mechanism with your cellphone and go home to fix your own.)

regards,

Jan 27, 2017 | Coffee Makers & Espresso Machines

1 Answer

Broke the plastic screen that goes to the cold water inlet valve?


The broken bit of filter has probably got stuck under the rubber diaphragm in the inlet valve. You will have to strip the inlet valve and remove the piece. There should be 3 or 4 screws holding the valve together. Make a note of how it comes apart. There will be a spring, a metal plunger and the rubber diaphragm inside the valve.

Apr 27, 2017 | Maytag Washing Machines

2 Answers

The black plastic piece the bobbin fit in is broken.


You may have a timing problem or bent needle. You will need to replace the bobbin basket if it is damaged.

Jan 28, 2014 | Singer 7466 Mechanical Sewing Machine

1 Answer

Cuisinart grind & brew - spring in the filter area popped out. not sure where it goes?


Yes, you place the spring into the tube at the back. When you replace the basket holder, make certain you reach in behind the holder and guide the spring into the proper place on the holder. (Otherwise the spring will be forced to a permanent bend and not work as well. Can't find replacements for this spring on Cuisinart's website).

As for why it pops out better now, when you removed the basket holder and cleaned it, you also cleaned the plastic guides on each side. In normal use, these guides acculuminate coffee and tend to get sticky or gummy. When the door pops open, the sticky rails grab the guides and slow the sliding action.

Cleaning them restores the clean guide rails to slide open on. (Next time you clean the basket holder, remember to reach in and wipe out all the inner parts, including the plastic rails that the basket holder slides out on. These get coated with coffee as well. And the place around where the grind basket fits over the ground basket. This area always gets sticky with old coffee. Just use a wet paper towel and clean everything. (But remember to be careful when you reinstall the basket holder so that the spring fits back properly.

Dec 04, 2017 | Cuisinart Grind and Brew 10 Cup Coffee...

1 Answer

How do I install a new Handle/Latch assembly on the door of a Whirlpool LHW0050PQ 4 Wash Machine...have to remove present one as broken---pull handle door catch does not release---have to release putting a...


I had to replace part No 8182408 - the washing machine door handle. There is a plastic bar in the middle of the assembly that broke because the door was opened too hard.

There are two springs, the latch, and the plastic piece that brings it all together. The smaller spring is the key, call it the L spring. It is shaped like an L and goes around the ends of the latch. The other spring is the larger and straight and goes around the tops of the plastic piece. The straight spring goes in with the crossbar facing on the outside of the washer. The latch with the L spring fits in between the plastic crossbar with the U shaped end pressing against the latches inside bar. The antenna of the L spring needs to wrap around the plastic bar and fit inside the straight spring bar. This applies pressure on the latch to stay closed. When the handle is pulled, it releases the pressure and allows you to open the door. The Metal bar is used to hold all the pieces together and once you have the alignment right, put it back into the door with the straight spring antenna tucked in the spots on the door, as well as the metal bar ends. Screw in the two spots that holds the assembly in place and you will be set. The door should open and shut easily.

Apr 22, 2011 | Whirlpool Washing Machines

1 Answer

The plastic piece that holds the headlight bulb is broke. Can I replace that piece without buying the whole headlight?


you might be able to find one at a salvage yard but you should be able to purchase that piece on it's own at the dealership.

Jan 03, 2011 | 1999 Nissan Quest

1 Answer

Saturn SL1 Shifter to Shiftstick


I had the same problem over a year and a half ago. I went to the closest Saturn dealership to get the replacement plastic piece. Turned out that the ENTIRE shift cable assembly was the smallest part that could be purchased to repair this. The cable assembly was over $200 at that time. I opted to forgo the ridiculous expense for this tiny little plastic part. True story: with a little heavy safety wire and a large washer I jury rigged the washer to hold the end of the shift cable in the fitting at the bottom of the shift stick. The washer acts as a keeper and the wire, wrapped in a basket around the back side keeps everything together. It still shifts reliably, a little looser than when it was new, but I saved $200 in parts (99% of which weren't broken) and probably a couple of hours of labor at least. One end of the cable assembly has to be attached to the transmission by the way and is not easily accessible. Sounds hokey but it really worked, still works!

Mar 08, 2009 | 1998 Saturn SW

2 Answers

HP 7410xi small plastic piece in print cartridge carrier broken


If the spring did not damage the carriage flex I would suggest just using some epoxy to hold the spring properly in place. If the spring did damage the flex (as shown in this picture) then you might contact HP and enquire about an extended warranty for this issue. In the US call HP at 1-800-HPINVENt.

Regards,
Bob Headrick, MS MVP Printing/Imaging

Dec 13, 2008 | HP OfficeJet 7410 All-In-One InkJet...

1 Answer

Spring came out - where does it go?


That is from your dripp stop. If you can replace it it will be in the bottom of your filter holder. If not Please tkae out the valve on the bottom of this filter holder. You will have no dripp stop but it will work just fine.

Jun 01, 2008 | Krups Aroma Control 197 Coffee Maker

1 Answer

HQ7825 Head retaining clip


The clip that holds the head closed and on broke. It is a small gray plastic piece. model speed - XL

Oct 21, 2007 | Philips Health & Beauty

Not finding what you are looking for?
Bosch TKA 9110 Coffee Maker Logo

567 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Coffee Makers & Espresso Machines Experts

graybeard32301

Level 3 Expert

382 Answers

Charles Tidwell

Level 3 Expert

475 Answers

DMS-UK

Level 2 Expert

81 Answers

Are you a Bosch Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...