Question about Husqvarna Rose

1 Answer

When pressing the foot control the machine won't run, it shows the presser foot blinking on the screen even when the presser foot lever is down.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,301 Answers

Check the connections, if they are good, your foot pedal has a short in it, so its not completing the circuit when depressed

Posted on Jul 15, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ishow me how to rewind the bobbin on a touch tronic 2001 singer sewing machine


Presser foot up, takeup lever at the top, thread the machine normally all the way and through the needle, open the needle plate, press the little lever to the right, wind the thread from the needle round the presser foot screw, press on the foot control slowly and wind the bobbin, when you have enough thread on the bobbin close the slide plate the winder will drop down, pull the threads to the back of the machine and start sewing

Oct 30, 2013 | Sewing Machines

1 Answer

The pressure foot handle is loose and my foot won't go down what's wrong


Grasp the presser foot bar and pull it down. It is likely that the loose bar has jumped off of the cam on the lever. you'll need to figure out how to get in there and tighten it or replace a broken lever.

Good luck.

Oct 11, 2012 | Singer 9900

1 Answer

The machine says the presser foot is not down and it is so it won't sew


it could be a problem with the motherboard, the sewing machine needs to be checked

Oct 10, 2012 | White Sewing Sewing Machines

1 Answer

Presser foot lever not working


does it feel loose and wiggly? A lever should feel firm as it works. If it does you'll need to get inside. Typically these levers have a cam on the other end that activates the presser foot bar. If it is loose it could have slipped off the part that makes that happen. Also the part on the presser foot bar can be broken but you won't be able to tell until you get in there.

Take your time and take pictures as you remove things. safeguard the parts... Good luck, I hope it's just loose.

Sep 07, 2012 | Toyota Sewing Machines

1 Answer

I have a 9960 singer machine and am trying to use the buttonhole presser foot for the first time and I can not get it to sew T


the buttonhole foot snaps on to the presser bar, there's a little lever at the back of the presser bar that releases the foot, then put the buttonhole foot down on the needle plate & use the presser foot lifter (number 11) to lower the presser bar down onto the buttonhole foot & you'll hear a click sound when it snaps on & make sure to use the buttonhole lever(number 31) because the machine won't sew a buttonhole unless that lever is pulled down.

Apr 26, 2012 | Singer Sewing Machines

1 Answer

Brother 834dp, entire machine is locked up??


the best thing would be for the machine to be serviced

Mar 08, 2012 | Sewing Machines

1 Answer

I have a singer inspiration 4210 and I'm trying to change the presser foot, I followed the instructions but pressing down on the screww does not snap the foot in place, I have tried using various...


I think you have to position the new presser foot under the shank then drop the presser foot lever down as if you were beginning to sew. This should snap the new presser foot right on. Be sure the little bar is positioned under the hook.

Jun 03, 2011 | Singer Inspiration 4205 Mechanical Sewing...

1 Answer

What instructions are there for a brother nx400 even-feed foot


Remove the screw holding the regular presser foot and the presser foot holder and set aside.

Place the take-up lever in the highest position.

Hold the even feed foot with your right hand with your thumb holding the lever of the foot in its highest position. Place the even feed foot on the presser bar and make sure that the lever of the foot rests upon the needle bar thumbscrew. While holding it in place, fasten the foot to the presser bar with the screw.

As the needle bar goes up and down, the lever on the even feed foot should rest on the needle bar needle serew and go up and down as well.

Jul 19, 2009 | Brother Sewing Machines

1 Answer

I am trying to use automatic button hole and it keeps beeping and showin bl?


Ok, so all the credit goes to this website http://www.burdastyle.com/howtos/show/95
Photo 7 shows a buttonhole lever that comes down and contacts the auto buttonhole presser foot. The machine manual is a little vague about this in the section about buttonholes. At the point when it shows the lever being pulled down, the manual should reference the part number in the list of part names in section 1, and it would have been easier for me not to have mistaken that lever with the stop on the side of the presser foot that the lever sits against . . . . that also kinda looks like a lever! Probably a no-brainer for someone who does this all the time, but for a noobie like me . . . .I'm glad I found the website above. So . . . .the machine is now making perfect buttonholes 30 seconds after finding the butonhole lever! Groovy!

John and Linda

e469e67.jpg
Buttonhole lever pulled down (presser foot not attached)

e011ff3.jpg Buttonhole lever resting against stop on presser foot
(Photos from burdastyle.com)

Jan 07, 2009 | Kenmore 19110 Computerized Sewing Machine

1 Answer

Doesn't sew


Hi emnsam....please update your post with the complete Model Number in it's entirety and I will be able to advise you.

Jul 29, 2007 | Husqvarna Rose

Not finding what you are looking for?
Sewing Machines Logo

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Sewing Machines Experts

radcal

Level 2 Expert

196 Answers

Douglas Plant
Douglas Plant

Level 2 Expert

222 Answers

sewcrazyshan

Level 1 Expert

19 Answers

Are you a Husqvarna Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...