Asko Logo

Asko Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 140 Products
  • 3K Answers

When the pump runs continuerly it is probably water in the bottom of the dishwasher, when you drag it out on the floor you can try to flip it to see if any water will run out of the mashine, or you an take the bottom front of to see if you can see any water, there should be a water float in the bottom that is being activatet by the water that can leak from the washing cabinet to the bottom of the dishwasher.

Asko Dishwashers | Answered on Oct 22, 2019 | 40 views

Text and videos here

Manual also mentions it

Asko Dryers | Answered on Oct 20, 2019 | 45 views

Apparently it is as much as a 16 year old model, and I could not locate instructions for that model, using https

There was a site with parts, however, but not a manual.

A similar model manual, for W6021, shows controls that may be similar.

Asko Washing... | Answered on Oct 12, 2019 | 54 views

I don't know but dryers generally are of a fairly crude construction designed to be cheaply assembled by the manufacturer and not so easy to repair.

The ones I have tackled, the belt replacement entailed removing screws until something important fell off and then on and on until the back of the cabinet could be separated from the front far enough to change the belt...

Asko Dryers | Answered on Oct 11, 2019 | 71 views

It is likely that the timer is stuck and will have to be replaced.

Asko Washing... | Answered on Sep 18, 2019 | 36 views

You will get a good idea here

Asko Dryers | Answered on Sep 13, 2019 | 66 views

It could be a faulty water inlet valve, but it could also be a blocked tube between the tub, and the water level pressure switch, because over time, this can become blocked, and affect how much water enters the machine.
An easy test is to put the machine on a fill cycle and then turn of the mains power to the machine as the machine begins to fill; if the machine continues to fill, it is probably the water valve; if not, check the tube from the tub to the pressure switch.
I hope this helps?

Asko Washing... | Answered on Sep 10, 2019 | 48 views

has the garbage disposal been replaced recently?
- check that the drain plug on disposal s popped out

check that the drain line has a loop in it, i prefer the high drain loop.

Asko Dishwashers | Answered on Sep 06, 2019 | 49 views

I had the same problem. Turns out the reset button on the back of the dryer needs to be pushed; when you push the reset button you should hear a click. If you do not hear a click the problem was probably not the reset button. The button shuts down the dryer heating elements if they are getting too hot and also keeps the drum from turning unless the start button is held down.

If you push the reset button and the dryer starts to work again, I strongly recommend that you stop the dryer and investigate why the heater elements overheated. In my case there was lint/hair build up on the heater elements themselves. Extensive dryer disassembly is required to properly clean the heating elements but it is worth the prevention of a house fire. While you're at it, clean the rest of the machine and the duct work.

Hope this helps

Asko T700... | Answered on Aug 23, 2019 | 2,191 views

If you are REALLY handy, look for a stuck relay. The timer may control the motor directly without triggering a relay. If that's the case you need a new timer. Usually the wiring diagram (schematic) is on a folded piece of paper stuck under the dishwasher or sometimes in back. I have seen a lot of stuck relays AND bad timers.
Good Luck

Asko Dishwashers | Answered on Aug 17, 2019 | 45 views

First of all, don't pre-rinse the dishes. Check the water temperature, it should be between 120 and 140 degrees. Be sure you are not partially blocking the dispenser door so that it isn't opening.

Asko D1976... | Answered on Aug 15, 2019 | 1,354 views

Does anyone have an Asko dishwasher model 1776 type dw953 for sale or are getting rid of

Asko Dishwashers | Answered on Jul 19, 2019 | 92 views

What is the belt part number for Asko DryerModel # T702C

Asko Dryers | Answered on Jun 27, 2019 | 1,402 views

If the main PCB is still pulsing the "beeper" even when unplugged, it would be the on board capacitors still charging it. Apart from changing the main PCB, I would suggest you leave it unplugged for as long as necessary to fully power down the capacitors. It will take a few hours or more. Try using the machine when it has stopped beeping. It may then be OK. If not, a board replacement will be the only solution.

Asko Washing... | Answered on Jun 10, 2019 | 40 views

I had tried several failed attempts to fix this problem. Finally I got on my knees and asked God to make the dishwasher run in Christ's name. The dishwasher just completed it's first cycle without any problems.

Asko 24 in.... | Answered on Jun 10, 2019 | 887 views

Hi Jacqueline,the filter will usually have a rubber o-ring gasket to seal the opening to prevent leaks. When you cleaned it,the gasket may have kinked, torn or popped out of the groove that holds it in place. Open the filter and check if the gasket is in place, if not slide it back into the groove and that should stop it from leaking. Also check the small drain hose, make sure the stopper is in. That should take care of any leaks in that area. If the leak continues I would suggest calling a local repair company. Hope that helps.

Asko Washing... | Answered on Jun 04, 2019 | 58 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Asko Experts


Level 3 Expert

85206 Answers

Lollo Pop

Level 2 Expert

134 Answers

Norman Worley

Level 3 Expert

1273 Answers

Are you an Asko Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides