Kitchen Ranges - Recent Questions, Troubleshooting & Support


SORRY NO CLUE AS WE ARE NOT SALTER TECH SUPPORT

Kitchen Ranges | Answered Yesterday


The wattage should be on the label where the power goes in. Watts divided by voltage equals the amps.

Similar to this and a 40 amp rating
https://products.geappliances.com/appliance/gea-specs/JB650SFSS

Kitchen Ranges | Answered 2 days ago


Broiler thermostat needs replacing? On an electric broiler it is dependent on the temperature the over is set to. On mine it I set it to 600, it glows red all the time, if I set it to 250 it is black heat and clicks on and off.

Kitchen Ranges | Answered 3 days ago


Contact centre for sa zenzele shown by internet search using https://www.google.com

Try calling them to see if they can assist. This is a repair oriented internet site, and cannot provide you with legal or financial advice, but out of courtesy, try their telephone number in South Africa:
Call centre 0861 900 903

Kitchen Ranges | Answered 3 days ago


could be several reasons, the striker could be having dirt/ grime and does not make contact. Or the striker is worn due to ware and tare. call a repairman,

GE Kitchen... | Answered on Jan 09, 2020


Hi,

The F10 F11 F12 F13 F14 Error Codes indicate that the electronic oven control board senses a runaway temperature condition in the oven through the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You could have a failed oven temperature sensor, a wiring harness failure, an open thermal switch or a failed electronic oven control board that would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect.
Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.

If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You would need to access the electronic oven control board (Timer) in the console and check the resistance at the sensor circuit connection to the control board as the next step in troubleshooting this problem.


http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Thanks to blueextc3221 for this solution.

Frigidaire... | Answered on Jan 09, 2020

Not finding what you are looking for?
Kitchen Ranges Logo

52,557 questions posted

Ask a Question

Usually answered in minutes!

Top Kitchen Ranges Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Paul Carew

Level 3 Expert

3484 Answers

Brad Brown

Level 3 Expert

18136 Answers

Are you a Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...