Danby Refrigerators - Recent Questions, Troubleshooting & Support


Turn off the refrigerator and remove the power cord from the wall socket.
Unscrew the thermostat / dial and gently pull it out of it's holder....
There is a tiny pipe on the back of the thermostat / dial.
Gently pull that tube out of the pipe that it is in.
The most likely reason for the lack of cooling is that there is a layer of gunk on that tube.
Take coarse cloth or pot scrubber and clean that tube gently...
Replace the tube in the pipe and see if refrigerator runs properly....
If not, new refrigerator needed....

Regards
Geoff

Danby... | Answered on Jan 06, 2020


The tray is located inside the toe panel at the bottom. Remove the tray carefully for cleaning as it will be full of disgusting effluent.

Danby... | Answered on Oct 31, 2019


  1. If the "HI", "LO" or "CL" error codes appear on the display for more than 5 minutes, a power reset may rectify the issue. Unplug the appliance, wait 5 minutes and then plug the unit back in. If the error code persists after a power reset, contact consumer care or an authorized service agent.

Danby DBC2760BLS... | Answered on Aug 26, 2019


should be behind back panel inside freezer

Danby DFF8802... | Answered on Aug 22, 2019


I also have a Danby Dkc146sldb. I tapped it full yesterday with a full CO2 Tank and dialed the psi to 10. I had a lot of foam even though it set for an entire day. The next night nothing came out. I played with tgeCO2 Again. I can hear gas going I but nothing coming out. I eventually got it working set itagain back to 12 psi (Bud light) and everything tasted fine. I increased the temperature a bit and today pulled the handle and once again nothing. This is very frustrating. Maybe I'm a dummy but can someone please tell me what I'm doing wrong? I pulled the release on the coupler into the beer keg and there's definitely has gas coming out. Please tell me something that might solve this prolem . I'm running out of ideas. Shouod I remove omething from the lines of "rings" going into the beer keg? I keep reading things about removing guts or reversing the ring? I'm really confused.

Danby DKC146SLDB... | Answered on Aug 18, 2019


Check the heater behind the panel in the freezer.I unplugged mine checked it and it seemed fine plugged back in .no more issues

Danby... | Answered on Jun 30, 2019


the list of causes --- yes on bad compressor will cause failure --as well as thermo safety -thermostat --low no freon --dirty condenser -fan failure --circuit failure -are a few

Danby... | Answered on May 09, 2019


hi before you may damage
install a new fan this can solve your problem

Danby... | Answered on May 01, 2019


Its probably the heater element. The Thermal cutout should be closed circuit. The bimetal can be open or closed depending on temperature. I am not familiar with these fridges. You will need to check the wiring diagram. Some open when they get warm, to allow a neutral path some close to complete the electrical circuit. Check for continuity of the bimetal when its been in the freezer overnight, then remove it and check if it goes open when warm (Or vice versa) If yours is an electronic defrost, it could be the board.

Danby... | Answered on Apr 10, 2019

Not finding what you are looking for?
Danby Logo

907 questions posted

Ask a Question

Usually answered in minutes!

Top Danby Refrigerators Experts

William Miller
William Miller

Level 3 Expert

9179 Answers

Cindy Wells

Level 3 Expert

6063 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Danby Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...