Frigidaire Kitchen Ranges - Recent Questions, Troubleshooting & Support
2 Answers
My oven is beeping F11. (i unplugged the oven
Hi,
The
F10 F11 F12 F13 F14 Error Codes indicate that the electronic oven
control board senses a runaway temperature condition in the oven through
the oven sensor circuit.
This can be caused by a faulty oven temperature sensor probe or a failed electronic control board.
Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit.
You
could have a failed oven temperature sensor, a wiring harness failure,
an open thermal switch or a failed electronic oven control board that
would cause this problem.
The first component to check would normally be the oven temperature sensor probe.
If
you have a volt/ohm meter, you can shut off the breaker for the range
and remove the screws that mount this sensor to the back wall of the
oven.
Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug.
You should have enough slack to pull it this far into the oven.
Disconnect
the sensor but do not let the wire harness retract back through the
back wall of the oven or it will be hard to reconnect.
Measure the
resistance of the oven temperature sensor with your volt/ohm meter. At
room temperature, the resistance should measure around 1100 ohms.
The resistance chart is shown in the image below.
If
the resistance is above 2200 ohms at room temperature, then the sensor
probe is causing the F10 error code and will need to be replaced.
You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.
If the resistance is normal, then one of the other causes mentioned above is producing your F10 code.
You
would need to access the electronic oven control board (Timer) in the
console and check the resistance at the sensor circuit connection to the
control board as the next step in troubleshooting this problem.
http://media.fotki.com/1_p,wbqdsfkrfqtswfqxgtqsskgwtqkq,vi/krdbrtqkgxkrbbqbrwb/1/1303472/5961857/image37801img-or.jpg
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.
Thanks to blueextc3221 for this solution.
Frigidaire...
|
Answered
on Jan 09, 2020
2 Answers
Replaced element, oven is still not heating
You may still have a bad Electronic Range Control (ERC). This is your timer that you mentioned. The oven is controlled by the ERC. There is a separate circuit for the BROIL and BAKE functions. Does the BROIL element still work? Or, are both elements not working? You may want to double check all your connections from the element to the control board as well. Sometimes the wire lugs can oxidize and not make good contact. Check the ERC to see if there any obvious signs of failure. Burned components are common. These boards are considered "non-serviceable" and usually requires replacing. You can attempt component-level troubleshooting if you are savvy with electronics. There's usually a basic block diagram that comes with your appliance mounted somewhere inside the operator console or on the back panel of the range.
The ERC for your range would cost in the neighborhood of about $100 - $140 to replace. Prices will vary between model versions and will also depend on where you get it. It is a very simple repair job if you wish to pursue this yourself. I can give you step-by-step instructions if you need further assistance. I hope this helps you.
PS The reason all your surface elements still work is because they are controlled by infinite switches behind the control knobs. There is a separate switch for EACH burner.
Frigidaire...
|
Answered
on Dec 23, 2019
14 Answers
Beeping F11 error on Frigidaire
Hi im an appliance tech and i had the same problem its not the EOC other words control board its actually the speed bake swith its stuck in the on position that why you get a stock keypad error code either f1 or f11 replace that switch or disconnect it and im positive that this will solve it .
Frigidaire...
|
Answered
on Jun 13, 2019
1 Answer
How do I turn the volume down or turn off the beep from my Frigidaire Gallery 5.0 cu. ft. Gas Range when the oven reaches its intended temperature?
As copied from the manual.
Setting a silent control panel
When choosing a function, a beep will be heard each time a pad is pressed. If desired, the control can be programmed for silent operation. Press and hold (start/time) . After 7 seconds, the control will beep once. This will block the controls from sounding when a pad is pressed. To return the sound, press and hold (start/time) again for 7 seconds until the control beeps once
NOTE!
The OVEN indicator light on the electronic display will turn ON and OFF when using the Bake feature and during preheat. This is normal and indicates that the oven is cycling to maintain the selected baking temperature. When the preheat indicator light turns OFF, your oven is ready.
Frigidaire...
|
Answered
on Jun 05, 2019
Not finding what you are looking for?
