Frigidaire Logo

Frigidaire Recent Questions, Troubleshooting Help & Support

  • 3K Products
  • 135K Answers
  • 3M Views

i don't know. be careful with electricity. if possible, try running normal washer load along with your dryer but with [no heat] 'cold air only' to see if they will keep running.
if they run OK, consider shutting off both washer and dryer. shut off main electrical panel and change fuses for both washer and dryer. turn hydro on and run both again
with your normal settings. if they fail again please call for repairs. my dryer would not run and although everything looked and tested out OK, i had to replace a small 6x8"
electrical box having 2 only 30 amp screw in fuses.
then it ran OK.

Frigidaire... | Answered on Oct 02, 2019


I had this same issue. My dryer would run and heat up but then stop and give me the f40. I measured all thermisters and everything was in range. The tech sheet stated that I needed to buy a new control board and I did. Same problem.
The solution was a loose connection on for p4. I took needle nose pliers and squeezed the connector to make it fit tight on the board and everything is working now.
Bottom line, expensive dryer with cheap connectors.

Frigidaire... | Answered on Sep 30, 2019


Hi- not sure if it will help but I had issues getting it out. What I found is the plastic casing (fridge) needed a little twist/push. Play with it- hold the filter in and GENTLY push/pull/twist slightly the fridge housing.

Frigidaire... | Answered on Sep 29, 2019


Cannot be answered with the information provided.

Need the serial number from the manufacturer's plate, which will probably tell you the year of manufacture.

Here is a link to Frigidaire: https://www.frigidaire.com/Owner-Center/Product-Support--Manuals/?productCode=FFBD2406NB

Frigidaire... | Answered on Sep 29, 2019


I would say that either the filter has split or the seal where it screws into the housing has failed. I would try a new filter and seal.

Frigidaire... | Answered on Sep 23, 2019


call FRIGIDAIRE AND LET THEM SOLVE IT IF INDEED BRAND NEW

Frigidaire... | Answered on Sep 22, 2019


AD is not an error code i found this out by goin to the frigidaire web site it just means that the dryer is in auto dry mode.

Frigidaire... | Answered on Sep 19, 2019


Unplug your refrigerator from the ac outlet, and 0open theref door for approx. 5 minutes. Then plug it again, after you hear the beeping close the door. wallah it's fixed.

Frigidaire... | Answered on Sep 18, 2019


There is a little bar that is on the ice bucket. That bar has to go into the middle of the plastic square that is on the back wall of the freezer. Try Pulling out the ice bucket, get a hair dryer and run the hair dryer on the back wall of the freezer right above the hole where that little bar goes. After you run the hair dryer for about 10 minutes or so put your finger in the hole and pull down on the plastic square. Make sure when you put the ice bucket back in the freezer, the bar goes inside the square hole, not under it, not over it. In it. If that doesn't fix the problem you probably just need a new solenoid. Part number 5304404333

Let me know how you make out. Good Luck

Bill

Frigidaire... | Answered on Sep 16, 2019


There are a number of reasons why this might be happening. You bets bet if to call a service guy out and let them take a look at it as some things require specialised equipment to troubleshoot.

Frigidaire... | Answered on Sep 14, 2019


Unplug it for 5 minutes. If that doesn't work, you may need to empty it of water by lowering the drain hose into a pail lower that the door.

Frigidaire... | Answered on Sep 14, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Frigidaire Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Frigidaire Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...