Frigidaire Logo

Frigidaire Recent Questions, Troubleshooting Help & Support

  • 3K Products
  • 135K Answers
  • 3M Views

Would need the model number
Either screws in front or snap spring clips

Frigidaire... | Answered on Jun 20, 2019


Would need the model number
Usually 2 screws through the plastic grill in the front
Or a snap spring clips are holding it in.

Frigidaire... | Answered on Jun 20, 2019


H1 means the refrigerator or freezer side is to warm
Are the controls set properly?
Is the rear wall of the freezer full of snow?
Is the outside edge of the refrigerator warm or hot to the touch?

Frigidaire... | Answered on Jun 20, 2019


Sounds like the defrost drain at the bottom of the freezer section is frozen over and clogged.
shut the refrigerator off, remove the food in the freezer
remove the shelves
remove the lower panel on the rear wall
at the bottom is the drain pan with a hole
my guess that it is full of ice?
use hot sink water and remove the ice
then use a turkey baster to clear the hole and the hose.
If the water still won't drain your going to have to manually clean the hose.

Frigidaire... | Answered on Jun 20, 2019


There are several websites with error codes listed. I have not seen any codes listed for frigidaire dryers. So I checked at Frigidaire.com had no luck there either. 800-374-4432 is their customer service number. I found codes for Frigidaire cooking products but nothing for dryers. Good luck.

Frigidaire... | Answered on Jun 18, 2019


The temperature control is located inside the freezer on upright models, and onthe left outside wall on chest models. The temperature is factory preset to providesatisfactory food storage temperatures.

However, the temperature control is adjustable to provide a range of temperatures for your personal satisfaction. If acolder temperature is desired, turn the temperature control knob toward COLD-EST and allow several hours for temperatures to stabilize between adjustments

Frigidaire... | Answered on Jun 16, 2019


Dear IFE KIARA,
Warning: If you feel in any way uncomfortable/unsafe performing this test or making this repair, please contact a qualified appliance repair technician.

F13 error is related to the clock. this error can occur when the clock looses communication between the keypad or any of the sensor in the stove, including the heat probe. sometimes resetting the power will fix the problem.
Try disconnecting power to the stove completely and flip the corresponding breaker on and off at the breaker box.
Wait 30 seconds and then turn everything back on.
if the problem persist after power-up, according to Frigidaire suggested corrective action the electronic oven control,also called EOC has to be replaced. Here is a search link from Google for the part in question.

Best of Luck,
JP
https://www.google.com/search?source=hp&ei=fecFXYCMAsKr5wKBm6G4DQ&q=316418735&oq=&gs_l=psy-ab.1.0.35i39l10.0.0..5525...1.0..0.209.209.2-1......0......gws-wiz.....10.8VUU1xaL8qM

Frigidaire... | Answered on Jun 16, 2019


Richard?
I have provided you a website that may help.

There has been a recall since 2013. Here below is the website.

My advice. Contact Gree. Be persistent and kind. Customer Support Reps, being people, can do wonders sometimes when they are treated kindly.

https://www.cpsc.gov/Recalls/2013/Gree-Recalls-12-Brands-of-Dehumidifiers/

Frigidaire... | Answered on Jun 16, 2019


Unfortunately, there is no good way I can think of to know without actually replacing the board. I recently replaced fans on a modern fridge (GE) only to be left with the control board being the only likely remaining suspect. Many on the internet posted that they had to replace the board to fix their problems. However, my brother was tired of trying to fix the fridge, and he got rid of it instead.

Frigidaire... | Answered on Jun 15, 2019


Hi im an appliance tech and i had the same problem its not the EOC other words control board its actually the speed bake swith its stuck in the on position that why you get a stock keypad error code either f1 or f11 replace that switch or disconnect it and im positive that this will solve it .

Frigidaire... | Answered on Jun 13, 2019


No household units use ammonia as a coolant. IF it did and it leaked, you would know it immediately. If the unit still works, there is no issue with the Freon that is in it. The odor could be a sealant that was used to make the interior of unit. You did not say how old it is. Freon can have an odor to it but the unit would stop working correctly pretty fast.

Frigidaire... | Answered on Jun 11, 2019


Did you disconnect and reconnect any of the electrical plugs? These are touchy and need to be tightly connected. Try some conductive lubricant on the connections, make sure they're as tight as possible. Wait 24 hrs then check for ice.
Hope this fixes it.

Frigidaire... | Answered on Jun 10, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Frigidaire Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Are you a Frigidaire Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...