Frigidaire Refrigerators - Recent Questions, Troubleshooting & Support


The pipe on the defrost drain has come off. Pul the fridge out and look for a pipe that goes to a tray on top of the compressor.

Also look for the drain channel in the back of the fridge. Something may have blocked the hole.

Or call the dealer under warranty.

https://www.frigidaire.com/Owner-Center/Product-Support--Manuals/?productCode=FFPS4533QM

Frigidaire... | Answered on Jan 21, 2020


Be aware the fridge works with deadly voltages. If you have not enough technical knowledge, please don't do this yourself.
With a multi meter you can measure if the voltage you apply is entering the fridge. There is not much in a fridge. You find a on / of switch, a thermostat en mostly an override switch too short a thermostat. So if you measure a voltage coming is, follow the wiring and check what the thermostat does. if it won't switch you have the cause. If it does switch, follow the wiring, and if the aggregate gets a voltage and does not run, you have a defective aggregate. I can't think of more.
Good Luck.

Frigidaire... | Answered on Jan 14, 2020


Good Afternoon Friend,

I understand that your Frigidaire refrigerator, model# FFHS2611LWF, is flashing an "H1" code. This is actually stating "HI", as in either the refrigerator or freezer, temperatures are Hi and not at a safe level. First, press any button to stop the alarm and clear the HI temperature. If you are still receiving the alarm, I suggest checking the freezer, to make sure that everything is still frozen, and nothing is defrosting as, well as checking the refrigerator temperatures. If things are defrosting or the temperature is Hi in your refrigerator, I suggest resetting your appliance, by either unplugging it or shutting the power off at your homes circuit breaker, for 3-5 minutes. When power is restored, Give your freezer 24 hours to stabilize at the default temperatures of 0 degrees for the freezer and 37 degrees for the refrigerator. I ask that you please follow up with a comment on the post, at your convenience, to advise if further troubleshooting is needed or if your refrigerator status has changed successfully.

-Best Regards-
WP

Frigidaire... | Answered on Jan 07, 2020


fan being obstructed behind back panel of freezer.fan motor failure or build-up of ice from door not shutting properly

Frigidaire... | Answered on Nov 27, 2019


The FRS26ZSH is a #for filter need MODEL #

Frigidaire... | Answered on Nov 27, 2019


Your Icemaker always makes solid cubes. Goes into bucket. your selection on the dispenser is not being recognized . Could be the control on the door (selector) . Also the selinod that switches from whole to crushed located at the assy behind bucket, Varies ON Model #

Frigidaire... | Answered on Nov 27, 2019


There is some truth to it. Refrigerant needs to flow from high pressure to low pressure, and refrigerant pressure is directly proportional to temperature. Once the temperature drops below 40*F, for the outdoor coil, refrigeration efficiency is lost. Some heatpump units need auxiliary heat because.
Cold refrigerant condenses, into a liquid, and a compressor will not compress liquid, why its valves and internals would chatter into pieces. There is such thing as compressor crank case heaters, or belly band heaters. A heater removes, evaporates liquid refrigerant from within a compressor, it is protection.

I would get a compressor heater, wraps around the compressor belly, near 50 watts, and can use a relay to switch off the heater when the compressor runs, or let the heater work continuously.

Frigidaire... | Answered on Nov 09, 2019

Not finding what you are looking for?
Frigidaire Logo

8,687 questions posted

Ask a Question

Usually answered in minutes!

Top Frigidaire Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

jasbo
jasbo

Level 3 Expert

2239 Answers

Are you a Frigidaire Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...