GE Dishwashers - Recent Questions, Troubleshooting & Support


Does it cycle i.e. fill, wash, rinse, and drain?

If yes, then heater relay likely has failed (closed).

What model number?

GE Dishwashers | Answered 7 hours ago


Sooo with my model just for anyone looking this up. My son loves pushing buttons and one of his favorite is the “delayed start” button. After researching, cleaning out the filter, unplugging the dishwasher and most everything short of pulling my hair out, I found out that the little nugget had pressed the delayed wash button. Which, you would think would reset when you reset the machine but evidently not. Pushed the delayed start button and cycled through 12 hrs and bingo, it ran....

Not a fun way to spend the night but at least I saved money by not having to call out a repair man. ??

GE Dishwashers | Answered on Dec 30, 2019


sorry we can not call the manufacturer as brand new should be under warranty

GE Dishwashers | Answered on Dec 13, 2019


The cycle timer may have "hung up".

GE Dishwashers | Answered on Dec 11, 2019


The one way flapper in the drain pump has broken off.

GE Dishwashers | Answered on Dec 05, 2019


Did you install it, or did the vendor install it?
If it is brand new, contact the vendor for assistance or replacement under warranty

GE Dishwashers | Answered on Nov 13, 2019


Shut off power to dishwasher at electric panel,shut off water supply,open door of dishwasher,remove screws on top side of dishwasher that are screwed into the underside of the countertop,,remove the front service panel on the bottom front face of the appliance by removing two or more screws on the right and left,locate and disconnect the water supply feed,locate and disconnect the electricity supply cable,locate and disconnect the drain hose usually connected to the drain of a nearby sink,pull dishwasher out of cavity in cabinet by grasping both sides of dishwasher with door slightly open,adjustment of front legs of appliance may be necessary.

GE Dishwashers | Answered on Nov 10, 2019


E4 means dishwasher sensor is detecting the dishwasher is over filling. First thing I would check is the float. You will want to make sure it travels up and down freely. Open your dishwasher door all the way. Look on the right hand side (could be in a different location on your model) you will see a round thing. Kind of looks like a air hockey pusher. Try moving it slowly up and down making sure it’s not stuck open.
If this didn’t work then I would lean towards a faulty sensor.
It’s possible you could have a faulty board as well.
It is my opinion unplugging it will have no effect on this particular issue.
I hope this information has helped. God bless and have a great day.

GE Dishwashers | Answered on Nov 06, 2019


I DON'T KNOW. INSPECT CHECK FUSES OR CIRCUIT BREAKERS. BE CAREFUL AND MEASURE FOR ELECTRICITY AT WALL RECEPTACLE.

GE Dishwashers | Answered on Nov 03, 2019


According to the GE repairman who visited, the solution is to close the machine (with the lights flashing). The machine starts and goes through the cycles, which it does rapidly and then all the lights turn off and the machine becomes silent after 1-1/2 to 2 minutes. Then the machine has been reset to normal. During this reseting period nothing happens inside the machine, although you may hear a running sound.

Thus, the solution is to run the machine in this flashing light state for the 1-2 minutes it takes to go raipdly through each cycle and then reset.

I hope this helps.

General Electric... | Answered on Nov 02, 2019


At first thought, it sounds like the control board has gone bad. Make certain it is properly plugged in. If no luck there, call the repairman.

GE 24 in.... | Answered on Oct 08, 2019

Not finding what you are looking for?
GE Logo

4,373 questions posted

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike

Level 3 Expert

4367 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Nathan Van Boven
Nathan Van Boven

Level 2 Expert

206 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...