Linksys Computers & Internet - Recent Questions, Troubleshooting & Support


https://www.linksys.com/ca/support-article?articleNum=140923

Which model?
Go to the Linksys website and download the instructions for your model of extender.

Linksys... | Answered on Dec 02, 2019


Access your router Setup page 
Open internet explorer go to http://192.168.1.1 (default) username: admin (default) password: "leave it blank" (default)
Go to Security go to Filter
if you know that Ipaddress of the computer you want to block for example 192.168.1.10
You can create up to five different IP Address Range filters   Users who have  filtered  IP addresses will not be able  to  access the  Internet at all   If you only want to filter one  IP  address instead of a range of IP addresses, enter the same  value into both fields  For instance, if you wish to filter the  PC with  the  IP  address of 192 168 1 5, enter 5  into both  fields on one line: 192 168 1 5 ~ 192 168 1 5 

if you know the MAC address of the computer click the Edit MAC Filter Setting and input the MAC address you want to block. 
blocking by MAC address is the most effective solution to block a computer... while blocking by ip address will be easily bypass by changing the ip add of the pc

then saved your settings and reboot..

Linksys BEFSR41... | Answered on Nov 27, 2019


Control Panel->add or remove programs-> Intel(R) PROSet/Wireless Software -> Modify -> Unmarked WI-FI PROTECTED SETUP

Linksys... | Answered on Nov 25, 2019


There are several factors that will affect or can cause problems in connecting your Roku to your Router.

If you're getting an error message on Roku like 014, 011, make sure to indicate it in your response. Normally, if you're getting 014 message, you can follow these steps:

. A simple power cycle resolves most of the issues. To perform a power cycle, please follow the instructions below:

1. Unplug the power cables from the modem, router and the Roku player.
2. Connect the power cable to the modem (after a minute). Once all the lights on the modem are lit, plug in
the power cable to the router and then to the Roku player.
3. Go to "Settings" and redo the complete Roku setup.

If the issue continues to occur, please try the channel 1 or 3. Should it persist, you may reset the Roku
player. Here is how:

On the back or bottom of the Roku unit, you should find a recessed little hole.
- Use a pin or paperclip to press and hold the button for 30 seconds (please ensure that the power light
blinks while you are holding it down).
The Roku device will reset to default and be ready for setup again.

If the problem continues, please reflash the software via the secret screen:
1. Press the "Home" button for 5 times.
2. Press the "Forward" button for 3 times.
3. Press the "Rewind" button twice.
4. Choose Update Software and the Roku player will then restart.

You can comment your serial number or the error message that you're getting. If your getting 011, just power cycle your entire network. Also, please make sure that you're not connecting the Roku to a Guest network. The speed of your connection matters as well. It should be atleast 1.5mbps.

Linksys... | Answered on Nov 23, 2019


The vent actuators are bad. there should be two. one on each side. they are small toy like motors that open and close the vents from within to allow the hot air to blow by closing the vents to the a/c unit.

Linksys... | Answered on Nov 21, 2019


You can get best linksys router support phone number at Toll Free Number ( 1-877-769-0969 ). Linksys router Tech Support number ( 1-877-769-0969 )

Linksys... | Answered on Nov 12, 2019


DO NOT CALL FAKE NUMBERS OR GO TO FAKE WEBSITES

Linksys... | Answered on Nov 11, 2019


this ones for you loser

Linksys... | Answered on Nov 10, 2019


Linksys router not support to work with landline.

Linksys router only can work with cable internet.

Linksys... | Answered on Nov 07, 2019


If you already have a cable router, then you don't want to use a wireless router. You will want to use a wireless access point instead.
The reason for this is that anything plugged-in to your cable router will not be able to access anything connected to the wireless router due to the NAT firewall in the wireless router.
If the wireless router has the option to make it a "Gateway", then that will fix this issue; otherwise, take the router back and buy a wireless access point instead.
As for how you hook up the wireless router to the cable router, you have to unplug the power cord of the cable router for about 15 minutes before hooking the Ethernet jack from it to the wireless router.
Once the 15 minutes have passed, you then can plug the Ethernet cable from the wireless router "WAN" port into an Ethernet port on the cable router and then plug-in the power cord of the cable router.
Once the cable router is finished syncing-up, the cable router should provide an IP address to the wireless router.
If you really have a cable modem instead of a cable router, then you won't have to put the wireless router into gateway mode.

Linksys... | Answered on Nov 02, 2019


Your message does not qualify as a question or query for a problem, try somewhere else
DO NOT MAKE THIS SITE WITH YOUR GARBAGE
Take your GARBAGE to another Side
Your message qualifies as SPAM

Linksys... | Answered on Nov 01, 2019


Default user names:
  • Linksys BEFW11S4, WRT54G: admin
  • Linksys EtherFast Cable/DSL Ethernet routers: Administrator
  • Linksys Comcast routers: comcast
  • All other Linksys routers: [none]
Default passwords:
  • Linksys BEFW11S4: [none]
  • Linksys Comcast routers: 1234
  • All other Linksys routers: admin

Linksys... | Answered on Oct 27, 2019


Have you secured your Linksys from unauthorized access?
The encryption code protects your wireless router from unauthorized access. The wireless card in your computer/laptop needs to be configured with the router's encryption settings before the computer/laptop can access the router.
For details on configuring the wireless router and the wireless card, please click on this link and follow my instructions :-
http://www.fixya.com/support/r3559128-wireless_router_security

Linksys... | Answered on Oct 27, 2019


Unfortunately this model of router has no support for directly connecting anything other than a printer that already supports Ethernet.

Since that's not the case with most consumer printers you will need to buy a "Print Server" These are made by all the main manufacturers, and come with a collection of interfaces, USB / Parallel of the printer, and Ethernet or WiFi of the network side.

They all pretty much do the same thing so go for one that meets your needs.

If my advices was at least helpful, please vote for me!

Linksys... | Answered on Oct 27, 2019

Not finding what you are looking for?
Linksys Logo

Family Lines

13,664 questions posted

Ask a Question

Usually answered in minutes!

Top Linksys Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a Linksys Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...