managemylife.com Computers & Internet - Page 6 - Recent Questions, Troubleshooting & Support


sounds like your heating element possibly

managemylife.com | Answered on Dec 21, 2013


So you want it to make ice water. And it comes out not frozen.
Is the water cold? if it is cold then it is making ice water ok.
Ice water is never frozen, only ice is frozen.

managemylife.com | Answered on Dec 21, 2013


-No.


Mai

managemylife.com | Answered on Dec 21, 2013


-There are feel things that cause a dryer not work:
-Thermal fuse, heater element, door switch, start switch an motor.

Good luck

Mai

managemylife.com | Answered on Dec 21, 2013


You could try this: http://www.repairclinic.com/Kenmore-Washing-Machine-Model-11026832692-ID-501837-Manuals-Care-Guides-Literature-Parts

It sounds like the belt or motor may have gone. Belts are pretty straightforward, I've replaced a couple over the years. The motor will take a bit more work. I also resolved such an issue by opening the electronics panel at the top of the machine and reseating all the connections.

managemylife.com | Answered on Dec 19, 2013


The belt could be stretched. The motor runs but can't overcome the inertia of the drum to achieve rotation.

managemylife.com | Answered on Dec 16, 2013


Try Retrevo Manuals.com lots of manuals but you really have to search for them. Make sure you gave make, model number etc.

managemylife.com... | Answered on Dec 16, 2013


You ran it dry at some point. Gas tanks collect crud and water at the bottom over time and this may have been sucked up into the fuel filter or carb. Clean or replace fuel filter, then remove and carefully strip apart and clean all parts of the carb be gentle with brass and any moving parts in the carb, clean with plastic tools.

managemylife.com | Answered on Dec 14, 2013


Turn the machine on its side or back or front so that the bulk of the fluid will be at the bottom when you add it. Fit the hose to this part, extend the hose other open end upward as high as possible. The pour the fluid into the hose end, when hose is full put your thumb over it and swing that end onto its hose connection and fit it without losing liquid.

managemylife.com | Answered on Dec 14, 2013


Robert,

Not sure if you have a commercial Refrigerator or not but view our "How to install your gasket" video this may be just what you were looking for.

Sincerely,
The Gasket Guide

managemylife.com | Answered on Dec 13, 2013


Jeanne,

If this is a commercial refrigeration unit we offer a custom made gasket option. It's a simple process at coolergaskets.com

Step 1: visit our custom made gaskets page HERE and identify the gasket profile material that best matches your existing gaskets.

Note: If you have a hard time with this we offer a $1 gasket sample ring.

Step 2: Input the outside edge dimensions you need your gasket to be (length and width) and how many sides it has (3 sided gaskets are most common for walk-in coolers/freezers, You will want precise measurements. Here's our "How to measure your gasket" video.

Step 3: Select the quantity you want and add that gasket to your cart where you will be able to proceed to check out there. Then relax because your gasket is in good hands!

managemylife.com... | Answered on Dec 13, 2013


On Samsung microwaves the SE error code flashed on display means "Sensor Error". This means that your humidity sensor has shorted and needs to be replaced. You will need to uninstall the entire unit and remove the outer shell to access the sensor that needs to be replaced. It will be mounted somewhere around one of the vent on the cavity of the microwave. You may contact Sears for the replacement part at 1-800-252-1698; M-F 6:30 AM-10:30 PM - Sat 7:00 AM-9:30 PM - Sun 7:30 AM-9:30 PM - All times Central.

managemylife.com... | Answered on Dec 12, 2013


This sounds as though the heater is overheating.

Ensure there is good airflow through the unit and dust the intake and output if necessary.

managemylife.com | Answered on Dec 10, 2013


Mine do that. The sensors located at the bottom on either side of the door have to "see" each other. It is very easy to bump them out of alignment. Check that first. It is possible that they are faulty, and replacements cost about $30. You can't, and shouldn't bypass these for safety reasons.

managemylife.com | Answered on Dec 10, 2013


Craftsman is a Sears brand. Do you have a local Sears store?? They should be able to help you.. If you don't have a Sears or a K-Mart, you can get on the internet and find an outlet for tool repair parts. That's how I find my lawn mower parts...

managemylife.com | Answered on Dec 03, 2013


This freezer has a refrigerant leak, and will only get worse. I am looking at the identical Kenmore model and the refrigerant is so low that a little frost forms on the capillary tube. I doubt that it is worth repairing. I can do my own repairs, but finding the leak is going to be near to impossible...

managemylife.com | Answered on Dec 03, 2013


I know this is obvious, but first check under shroud and see if a block of wood is jamming blade. If not it's a bad bearing. If you are not able to repair yourself, look in yellow pages for a electric motor repair shop. Ask if they will repair it for around 50.00 labor and they should bite. Bearings should run 15 to 30.00 times 2. Do not know what brand it is but should be cheaper than new motor. Also ask them to replace brushes if needed, and you should get many more years of use. Sorry, remove motor before you take it for service, or they will charge you an arm and a leg.

managemylife.com | Answered on Dec 02, 2013

Not finding what you are looking for?
managemylife.com Logo

195 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top managemylife.com Computers & Internet Experts

thinksewfast

Level 2 Expert

89 Answers

Brad Brown

Level 3 Expert

18157 Answers

Paul Bade

Level 3 Expert

1662 Answers

Are you a managemylife.com Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...