Computers & Internet - Page 9 - Recent Questions, Troubleshooting & Support

take the hinges off or if it dosent work call the refrigerator people and get them to sort it out for you | Answered on Aug 13, 2013

The switch under the seat is not working. The switch needs to close to allow the engine to continue to run when the clutch is released. This is a safety thing in case you are knocked off the tractor. Check the wiring, connection, and the switch. | Answered on Aug 08, 2013

follow this steps and fix it. God bless you
is it getting water into the mold?
  • Is there power to the icemaker? (voltage check)

  • Check for cube lodged in ejector arm
  • e39244f2-59a1-4c9e-a1e2-5731ead02bc7.gif | Answered on Jul 30, 2013

    The bit the keeps the switch locked is probably broken. You'll have to replace the switch and the dryer should be fine again. | Answered on Jul 24, 2013

    What make and model device? | Answered on Jul 23, 2013

    merci | Answered on Jul 15, 2013

    This is not a website question. Please ask this question in another category. | Answered on Jul 04, 2013

    i use WD40 to clean also spray head before use this keeps the head clean at least it does with my strimmer | Answered on Jul 02, 2013

    pc623 | Answered on Jul 02, 2013

    Refer this problem to Sears for resolution | Answered on Jun 07, 2013

    Sorry, this is in the wrong category | Answered on May 31, 2013

    This question is in the wrong category! I dont think its anywhere related to Websites! | Answered on May 31, 2013

    The dehumidifier needs to have the control set correctly and the fan and the compressor to run in order to remove moisture from the air. The fan pulls the warm, moist air over a cold coil where the moisture condenses into water. Cool, dry air is expelled from one side and warm dry air from the other.
    If the unit is low on refrigereant, the compressor will not run - nor remove moisture. Likewise, the control must be set right, too. Finally, most unit rely on a float switch or a tank switch to determine if the tank is full or present. If the float switch or tank switch is jammed due to tank position, it may prevent the unit from running. Remove & carefully reinstall the tank to see it that solves the problem.
    Good luck! | Answered on May 29, 2013

    The Dial Control is bad and will not go past OFF, needs to be cleaned or replaced | Answered on Apr 12, 2013

    check the thermostat, if the compressor is running, the fridge is low on gas | Answered on Mar 30, 2013

    clean and put in side baking soda. | Answered on Mar 06, 2013

    Most Kenmore appliances are available from . The direct link to the installation manual for the 110.26852500 is . The directions for leveling the washer is on page 7. To level the front of the washer, tip the washer back and place a wooden block under it. Then adjust the front legs up or down. Use a level to check both the front to back and side to side level. (You may need to loosen the lock nut to move the legs. Then return the nut to the position tight against the bottom of the washer. The appropriate wrench is a 9/16" or 14mm.) The back legs should adjust themselves when the washer is tipped forward until the back of the washer is about 4" off the floor.

    I hope this helps.

    Cindy Wells | Answered on Feb 15, 2013

    Not finding what you are looking for? Logo

    195 questions posted

    Ask a Question

    Usually answered in minutes!

    Popular Products

    Top Computers & Internet Experts


    Level 2 Expert

    89 Answers

    Brad Brown

    Level 3 Expert

    18157 Answers

    Paul Bade

    Level 3 Expert

    1662 Answers

    Are you a Computer and Internet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides