Rustoleum Tools & Hardware - Others - Recent Questions, Troubleshooting & Support


Pull the nozzle straight up and out. Grab a nozzle from another can that looks to be the same and try that one. You may have to try multiple nozzles. You can also buy nozzles on ebay, but they are usually more than the price of the can.
If this doesn't work, then the can may be faulty, or if very old (many years) it may no longer have pressure even though there's still paint inside.
Another thing to check is if the ball inside rattles when you shake the can. If it doesn't, the paint might be hardened in the can.
Remember next time you finish painting to wipe off the nozzle, turn the can upside down and spray until almost no more paint is seen.

Rustoleum... | Answered on Sep 27, 2016


either defective sprayer or no propellant either return or try different spray tip

Rustoleum... | Answered on Sep 27, 2016


the product data sheets states that:
PAINTING If surfaces are to be painted in the future, remove Rust Inhibitor from the surface with a solvent such as acetone or mineral spirits prior to painting.

Rustoleum 224284... | Answered on May 05, 2015


Usually when you have cracking on your windows, there's several variables including sunlight. One of the biggest problems is using the incorrect primer or a cheap paint. Contrary to what many believe, a primer that dries extremely hard is not ideal for exterior surfaces. Wood expands and contracts with heat, cold and moisture. A high quality latex primer, topped with a high quality exterior latex paint will give you the best results. It allows for flexibility but offers great protection. Some prefer an oil/alkyd based primer. This is fine as long as it's a slow drying primer. The quick drying primers have hardeners in them that don't flex well. Be sure to remove any loose and flaking paint before you prime them. There are places where you can cut corners with painting. I wouldn't do it on exterior paint. One last thing to be aware of- be sure it's not lead paint you're working with. That changes everything.

Rustoleum... | Answered on Oct 31, 2014


make sure you prime the rubber first.....ask the manufacturer (website), or local paint store manager.
Good luck
Neil

Rustoleum 214945... | Answered on Sep 27, 2014


Repainting without adequate drying time will cause this. Make sure paint is dry. Use 180 grit sandpaper in swirling pattern to sand down the problem areas, idea is to feather edge the paint so you don't feel and ridges between the transition layers when you sweep your hand over them. Then prime the bare metal, then repaint entire door for best results.

Rustoleum... | Answered on Aug 26, 2014


If latex based paint was used, most of the time it is, spray the area with warm water then use a flat scraper to remove.. It is very messy when doing a large area. Cover as many surfaces as you can to protect. Try a small area in a corner first to see how it will work, if it works fine then do the whole wall.

Rustoleum Rust... | Answered on Aug 26, 2014


Ensure the surface is clean AND wax free.

Rustoleum... | Answered on Apr 13, 2014


Didnt give much info to go on lol. Make /model and a little more detail on your issue will be needed before anyone can try to help you

Tools & Hardware... | Answered on Nov 13, 2019


In all ro systems filtering sea-water or brackish water, there should be much more waste water than potable water produced. You didn't say if the system is producing potable water. If you can give more information about your inlet water and the quality of your potable water quality I may be able to help.

Tools & Hardware... | Answered on Nov 13, 2019


Leaky seal most likely, or a broken spring, or worst a bad valve. Check the seal first, then the spring, then the valve. Always check the cheapest thing first.

Tools & Hardware... | Answered on Nov 02, 2019


Hello Gayle,

I found this video and I hope it helps you out.
https://www.youtube.com/watch?v=wWOubLQ5luc

Good luck,
Andrew

Tools & Hardware... | Answered on Oct 31, 2019


Have to pull off the front face and panels access from the front of machine

Tools & Hardware... | Answered on Oct 25, 2019


Do you mean tremclad? You can either leave it alone and hope it eventually dries, or you can remove it and try again with the right kind of paint. tremclad was made for metal and rust, not cupboards. I suggest you wipe it off with a suitable solvent, perhaps acetone will work. Once you have as much off as possible, sand down the cupboards and paint with latex or even oil base house paint, or if you sand all the paint off you could use a stain. At any rate, use the right product for the job.

Tools & Hardware... | Answered on Oct 23, 2019

Not finding what you are looking for?
Rustoleum Logo

10 questions posted

Ask a Question

Usually answered in minutes!

Top Rustoleum Tools & Hardware - Others Experts

Strech
Strech

Level 3 Expert

1562 Answers

Rouand Sido
Rouand Sido

Level 1 Expert

6 Answers

john h

Level 3 Expert

22486 Answers

Are you a Rustoleum Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...