Sunbeam Heating & Cooling - Recent Questions, Troubleshooting & Support


have same problem with heating pad . reset control by unplugging unit for 1 minute , while holding down power button plugged unit back in . sometimes this takes 3 or 4 tries.

Sunbeam 805810... | Answered on Nov 03, 2019


Generally means u have a bad connection at the wall or at the control module. Disconnect everywhere u can and reconnect

Sunbeam Heating... | Answered on Sep 09, 2019


Try unplugging the power cord from the wall socket and check that the connection to the blanket is good and not loose. Then plug back into the wall socket and switch on. If error still occurs then there may be a problem with the blanket.

Sunbeam Heating... | Answered on May 17, 2019


I had checked the "connection" at the blanket before but after reading this I unplugged it from the wall and re-checked the plug in at the blanket. It's not flashing anymore and it seems to be working.

From Sunbeam's site:

Q: What does "FF" mean on display of my control?
A: If you have a digital control, it is designed to flash "FF" on the display to notify you that a problem may have been discovered. Gradient controls and warming throw controls use a blinking indicator light for this purpose.

Follow the instructions on the flag tag to reset the control or follow the steps below.
  • Unplug the system from wall outlet.
  • Check that the control is well connected to the module.
  • Plug the power cord into the wall outlet.
  • Set the control to "on".
If the system still does not operate, disconnect the power cord and Contact Us.

Sunbeam Twin... | Answered on May 13, 2019


The auto shutoff function may have failed and the blinking may be indicating the fact.

Sunbeam 722 Auto... | Answered on Feb 14, 2019


Probably means the pad has failed and will have to be replaced

Sunbeam Heating... | Answered on Feb 05, 2019


What the actual F???

Sunbeam 722 Auto... | Answered on Jan 23, 2019


I am trying something now as I was told F2 requires you to check the blanket for wear and tear and plug it back in. 3 times doing this should be sufficient. If it still reads F2 it's "gone" Ours is new so it shouldn't be "gone" but here's what I found...Where the plug goes into the blanket there are 4 holes for 4 silver pins. I noticed the 3rd pin was a bit lower than the other 3. It will not move up with pliers so don't force it just return it. check there

Sunbeam 722 Auto... | Answered on Jan 19, 2019


If you have the same heater i do then in between the elements at the bottom there is a safety swith that bends when it heats up and breaks the connection Dont mess with it plugged in it will shock the hell out of you but if you bend it down it wont be able to lift off the circut and will stay running untill you turn it off

Sunbeam Heating... | Answered on Dec 29, 2018


Wires probably damaged inside. Be carefull, I had one cought on fire. Dont like this things ever since

Sunbeam Heating... | Answered on Dec 28, 2018


unplug replug blanket to control connectors plug back in
this will continue to happen on these blankets you will have to reset these blankets again and again (chinese junk)

Sunbeam Heating... | Answered on Dec 22, 2018


http://www.electricblanketinstitute.com/blanket-or-comforter-on-top-of-electric-blanket.html

Sunbeam Heating... | Answered on Dec 10, 2018


TIME TO CHUCK IT AND BUY NEW

Sunbeam Heating... | Answered on Nov 21, 2018


Could be controller failure since it flashes ff with or without the blanket connected

Sunbeam Heating... | Answered on Nov 01, 2018

Not finding what you are looking for?
Sunbeam Logo

381 questions posted

Ask a Question

Usually answered in minutes!

Top Sunbeam Heating & Cooling Experts

Felizardo Erilla
Felizardo Erilla

Level 2 Expert

241 Answers

Paul Carew

Level 3 Expert

3480 Answers

Pete Norton

Level 2 Expert

121 Answers

Are you a Sunbeam Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...