Tissot Watches - Recent Questions, Troubleshooting & Support

there usually is an AC contact point to reset digital watches. Touching the + and the ac point with a conductive wire usually resets the watch. Not sure about the spring- I'm not going to open my Tissot up unless I have to.

Tissot T-Touch... | Answered on Dec 16, 2019

Try Googling (tissot)(T670)(manual) without parens for instructions.

Tissot Watches | Answered on Nov 09, 2019

Steps to Synchronize the Hands
  1. Press the centre pusher (T). The watch should beep once.
  2. Touch the centre of the touch-sensitive face until opt appears, in opt select 24H Cm (or 12H Fft or 24H Fft or 12H Cm) is shown in the digital LCD display.
  3. Press and hold the centre pusher (T) for approximately 5 seconds. The watch will beep once and then again, a second time, after 5 seconds have passed. After the second beep, the digital LCD display should read SYNCHRO. If not, return to step one.
  4. Press the upper pusher (+) to advance the hour hand until it is positioned exactly at 12:00. (PH press T button to to switch to minute hand adjust)
  5. Press the lower pusher (-) to advance the minute hand until it is also positioned exactly at 12:00.
  6. When both hands are aligned together and pointing directly at 12:00, press the centre pusher (T) to save the setting. The hands of the watch are now synchronized

Tissot T-Touch... | Answered on Nov 05, 2019

Can I assume this is a quartz powered watch? If so, sometimes, if thger bettery is either old or has started leaking hen is causes misfires in the time regulator.. First step would be chasnge battery & resdet the watch & monitor it. If this does not work, then put it into a Tissot service centre. Ifts not a quartz movement, there is no fault in a mechanical movement really that could cause this.
Hope this helps.

Tissot Watches | Answered on Oct 06, 2019

it all stems from the watch not actually being waterproof it's more water resistant than waterproof. The little indentations on the back that look like they are for a tool to unscrew it are actually holes i guess for the altimeter and meteo so it can sense pressure. Behind the back just behind the holes is a nylon gauze material and underneath this is a sensor slightly recessed and covered with some kind of waterproof substance. As far as i can see the problems lie here any water sweat or other foreign object than gets into this gauze will eventually will clog this gauze material which at first will affect the altimeter then the meteo. When the gauze has been clogged up severely i gets very dirty indeed which means when it gets wet it takes an age to dry out so if you wear it in the shower like i used to it will never dry out this causes the watch to malfunction quite severely. You can actually fix this problem yourself just get a very small flat screwdriver and lever the back off don't worry it's only a push fit and comes of easily you will see straight away a dirty damp smelly clogged up round piece of nylon gauze clean this up with a bit of WARM not boiling soapy water being careful not to disturb the pressure sensor and it's waterproof goo inside then dry it all and put it together
Hope this helps

Tissot T-Touch... | Answered on Sep 17, 2019

Take your Tissot to a jeweler who will open it, identify the battery type, and perhaps install a new one.

Tissot Watches | Answered on Jun 15, 2019

From your description it could be the main spring is broken, or there is a gear and or bushing failure. You will have to give the watch to a place that can service your watch. If you contact Tossot customer support they can advise you.

Tissot Watches | Answered on Apr 29, 2019

Take your Tissot two timer to a jeweler for battery identification.

Tissot Watches | Answered on Nov 13, 2018

A water resistant watch usually has a back that screws into the case and seals with a rubber O ring.

Sometimes the back can be very tight to unscrew so even with the dedicated wrench it is difficult to remove without damage to the case. The professional would disconnect one end of the bracelet and clamp the case into a special holder.

Once a non-dealer has replaced the battery it is usual to discover the back isn't replaced as tightly as original - this is reflected by the usual warning the watch will no longer be waterproof. The only way to retain the waterproof or water resistant quality is to have the battery replaced by a dealer or manufacturer when it will be, if required, pressure tested.

Tissot Watches | Answered on Nov 05, 2018

Take your Tissot to a jeweler for battery identification and replacement.

Tissot Watches | Answered on Nov 05, 2018

Not finding what you are looking for?
Tissot Logo

Family Lines

670 questions posted

Ask a Question

Usually answered in minutes!

Top Tissot Watches Experts

Janelle Schoonover
Janelle Schoonover

Level 3 Expert

842 Answers


Level 1 Expert

3 Answers

Vernon Taylor

Level 3 Expert

6103 Answers

Are you a Tissot Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides